Electronic – Configuring a 7-Series GTXE2 transceiver for Serial-ATA (Gen1/2/3)

Hello this will be an experts questions 🙂 You should be familiar with the following topics

• Xilinx Multi-Gigabit-Transceivers (MGTs), especially the 7-Series GTX/GTH transceivers (GTXE2_CHANNEL)
• Serial-ATA Gen1, Gen2 and Gen3, especially Out-of-Band (OOB) communication

Question:

How should a GTXE2 be configured for Serial-ATA?

OOB signaling is not working neither RX_ElectricalIdle nor ComInit.

Introduction:

I implemented a SATA controller for my final bachelor project, which supports multiple vendor/device platforms (Xilinx Virtex-5, Altera Stratix II, Altera Stratix IV). Now it's time to port this controller to the next device family: Xilinx 7-Series devices, by name a Kintex-7 on a KC705 board.

The SATA controller has a additional abstraction layer in the physical layer, which is based on SAPIS and PIPE 3.0. So to port the SATA controller to a new device family, I have only to write a new transceiver wrapper for a GTXE2 MGT.

As of Xilinx's CoreGenerator doesn't support the SATA protocols in the CoreGen wizard, I started a transceiver project from scratch and applied all necessary settings as far as they are asked by the wizard. After that I copied the GTXE2_COMMON instantiation into my wrapper module, ordered the generics and ports into a meaning full schema.

As a third step I connected all unconnected ports (the wizards doesn't assign all values !!) to their default values (the default from UG476 or zero if not defined).

In step 4 I checked all generics and ports again against the UG476 if they are compatible to the SATA settings. After that I connected my wrapper ports to the MGT and inserted cross-clock modules if necessary.

As of the KC705 board has no 150 MHz reference clock, I program the Si570 to supply this clock as "ProgUser_Clock" after each board "bootup". The MGT is in powerdown mode (P2) while this reconfiguration. When the Si570 is stable, the MGT is powered up, the used Channel PLL (CPLL) locks after ca. 6180 clock cycles. This CPLL_Locked events releases the GTX_TX|RX_Reset wires, which cause a GTX_TX|RX_ResetDone event after additional 270|1760 cycles (all cycles @ 150 MHz -> 6,6 ns).

This behavior can be seen in chipscope, captured with a stable, uninterrupted auxiliary clock (200 MHz, slightly oversampled).

So the GXTE2 seams to be powered-up, operational and all clocks are stable.

GTXE2 ports to control the OOB signaling:

The MGT has several ports for OOB signaling. On TX these are:

• TX_ElectricalIdle – forces TX into electrical idle condition
• TX_ComInit – send a ComInit sequence
• TX_ComWake – send a ComWake sequence
• TX_ComFinish – sequence was send -> ready for next command

On RX:

• RX_ElectricalIdle – RX_n/TX_p are in electrical idle condition (low-level interface)
• RX_ComInit_Detected – a complete ComInit sequence was send
• RX_ComWake_Detected – a complete ComWake sequence was send

Detailed error desciption:

1. TX sends no OOB sequences if TX_ComInit is high for one cycle.
2. RX_ElectricalIdle is always high

Tests:

1. SATA loopback cable: cut a SATA cable and solder the apropriate wires 😉
   — I'm using a special SFP to SATA adapter, which extends the KC705 with a SATA connector – http://shop.trioflex.ee/product.php?id_product=73
2. SMA loopback cables: I moved the MGT and connected the LVDS wires to the SMA jacks and installed 2 SMA cables as cross-over.
3. I programmed my old ML505 (Virtex-5) with onboard SATA connector to send ComInit sequences. The 2 boards are connected with a special SATA cross-over cable.
4. I connected a HDD with a partial stripped SATA cable to the KC705 (SFP2SATA adapter) and connected a 2.5 GSps scope (yes the signals are undersampled, but it's good to see bursts and idle periods…).

Experiences:

• Test 3 shows transmitted OOB sequences from Virtex-5 to Kintex-7 but the ChipScope trigger event does not occur – Rx_ElectricalIdle is still high.
• Test 4 shows no transmitted OOB sequences on the cable.

Should I post parts or the complete transceiver instanziation?

only the instance has ca. 650 lines 🙁

Appendix:

Electrical idle means that the MGT drives both LVDS wires (TX_n/TX_p) with common mode voltage (V_cm) which is in range 0..2000 mV. If this condition is met, the common mode delta voltage is less than 100 mV, which is referred to as ElectricalIdle condition.

OOB-signaling means that the MGT transmits bursts of electrical idle and normal data symbols (D10.2 in 8b/10b notation) on the LVDS wires. SATA/SAS defines 3 OOB sequences call ComInit, ComWake, ComSAS which have different burst/idle durations. Host controllers and devices use these "Morse signals" to establish a link.

Edit 1:

After setting Common Voltage Trim (RX_CM_TRIM) and (Differential Swing Control) TXDIFFCTRL to maxima and connecting TX_ElectricalIDLE and TX_ComInit to push buttons, I was able to see some little results:

1. TX_ElectricalIDLE is working, but the TX OOB FSM not (TX_ComInit, TX_ComWake)
2. if TX_ComInit is high for ever, the transceiver transmitts ALIGN primitives but at a quarter of the correct clock circa 375 MHz instead of 1.5 GHz
3. RX_Electrical IDLE is still not working

I also tried to use the alternative OOB clock, but this has no effect.