Electronic – How to capture analog signal from a speaker magnet

amplifieranalogaudiodesign

UPDATE: Thank you all for your input! Looks like I'll be tapping the speaker outputs instead. Please see the new question.

Although I have lurked these forums for a while, and even though I tried to research this question beforehand, this is still my first question. Please excuse any faux-pas…es. (Fauxes-pas?) Anyway:

I have a musician friend who plays keyboard, and for his birthday, we bought him a kid's DJ toy as a joke. It's a very cheap plastic toy with some low-quality samples and a small keyboard. He would like to use it in performances, but there are no line/headphone outputs, only a small speaker (2.5 3 W, 8 Ohm if I recall correctly, I can get the exact specs if necessary). Shoving a microphone against this speaker, although certainly a workable last-ditch solution, is something he would like to avoid.

I pulled it apart, but to no avail: the speaker wires are connected to the outputs of a TDA amp chip (TDA2030 if I recall correctly TDA2822L, see image below), the rest of the PCB is featureless. Even if I could identify where to tap into the circuit for a suitable signal, the quality of the PCB and the components makes me doubt it would survive de-soldering.

Instead, I'm wondering if it's feasible to generate a signal from the oscillating magnetic field of the speaker (similar to how an instrument pickup works). I imagine it would consist, at minimum, of a coil in close proximity to the speaker and an external load. I'm by no means an expert in analog circuit design though, so I don't know if this is even possible.

Some additional info:

  • I can design PCBs and I have an affordable fabrication option, so solutions requiring PCB mounting are welcome (through-hole only, please).

  • If possible, please avoid suggesting specialty components, as these might not be available at my location (Hungary), or it might be prohibitively expensive to ship them.

  • Ideally, the output signal would be similar to that generated from an electric guitar. Barring that, line level signal would also work.

  • I would like the circuit to feature some sort of volume control, and possibly a tone knob (again, similar to an electric guitar).

  • Distortion, uneven frequency response, etc. are not a problem. Knowing my friend, I imagine the less "sterile" the sound, the happier he will be with it.

I can provide further specs or pictures if necessary. Any help is greatly appreaciated!


Update:

The original post contained a typo (25 W speaker instead of 2.5 W). Not that it matters, because I misremembered anyway, it is 3 W.

Also, based on the initial answers, it seems I have given up on the PCB too soon! The amp chip is a TDA2822L (see full markings in image below). If the datasheet is to be believed, Output 1 (pin 1) is connected to the speaker's "-" input, while Output 2 (pin 3) is connected to the speaker's "+" input. As requested, I am including images of the PCB:

PCB back side, with TDA chip near the top left corner. The white wire runs to the speaker's "-" input, the yellow wire runs to the speaker's "+" input.

back side of the PCB

Closeup of the TDA chip. As far as I can tell, the marking is:

UTC 0CC7
TDA2822L
      01

I don't have my multimeter handy right now, so I can only go by the markings here. The two resistors below the glue blob are either 4.7 Ohms or 47 MOhms (the third band alternates between green and gold pretty evenly). The two ceramic capacitors (between the resistors, partially obscured by the white wire) are marked "104", so I'm assuming they are 100 nF. The outputs of the TDA (pins 1 and 3) are connected to the speaker wires, as well as to resistor->capacitor->ground.

closeup of the TDA chip

PCB front:

front side of the PCB

PCB front, closeup of (what I assume to be) the amp circuitry.

front side of the PCB, amp circuit

PCB front, closeup of the TDA area. The chip is facing downward (i.e. pin 1 is on the lower left).

front side of the PCB, TDA area

Although I remembered the PCB to have next to no markings (mostly just repeating the button labels), I did find this marking. Not sure if the second character is a zero or a capital o. Google turns up nothing either way, but who knows, maybe someone will find it useful.

serial number found on the PCB

Finally, an example of why I am uncertain about the quality of this particular PCB.

mouse bites of dubious quality

Best Answer

Given the vastly changed info... TDA2822 is a low power chip (under a 1W; its datasheet recommends it for "portable cassette players"), and of course the speaker it sends to is only 2.5W (doesn't get that much). Basically you can take the output of this amp (from the speakers' wires) straight to any professional line in audio equipment. It's like plugging in a walkman. No divider or anything like that is needed. Professional equipment accepts "hotter" signals than the consumer ones; see line level. Check with a voltmeter just in case that you don't get way over (say no more than 2V RMS on whatever it blasts the loudest), but there's not much else to do.

Also the quality of the PCB isn't great... but do you want NASA standards in toy using a $0.10 chip? The last image are "mouse bites", but those are normal.

Regarding the power supply info (added in a comment): 7.5V is how they get this chip to make enough sound for a loudspeaker. Likely the TDA2822 output doesn't get to the rails (i.e. it's less than 7.5V peak); most amps can't swing all the way to the rails, typically they can go up to 1V or 2V under. Some of the more dinky mixing consoles I've seen the innards of have only 6.3V rated caps on inputs; that mixing console was powered from 6V. So... there's potential danger of damaging a mixing console over a long period of time if this toy outputs to its max volume; we're not talking about immediate fireworks. If the mixing console is powered by more than 6V supply chances are good it uses higher-rated caps on inputs so the danger of damage becomes practically nil. If the mixing console is a profi one it will have maximum input level somewhere in its (service) manual. For example, a TASCAM I have specifies maximum input level as +18dBv (8 V).