mosfet-driveropto-isolator
I need to drive a solenoid with a MOSFET. The solenoid is an 8W solenoid and it will be connected to a +12V voltage.
And this drive command have to be isolated with an optocoupler but I don't know how to choose it.
What characteristics do I need to watch in the datasheet? What is important? Are there some good brands and some bad ones?
You could connect a buffer like SN74LVC1G240 instead of the transistor to control the output of IC2.
The output of IC1 goes to the Output Enable input of the buffer. The output of IC2 goes to the A input of the buffer.
When the EN is high, the output of IC1 is low, enabling the buffer output. When the EN is low, the output of IC1 is high, disabing the buffer output (floating).
I think this should work, but please double-check before ordering parts ;-)
The OPTO's emitter should be grounded, and the junction of its collector and R3 should be connected to 555 TRIGGER.
the formula for determining the 555's timeout is t = 1.1RC, so with 45K and 0.1\$\mu\$F in there, the the output pulse will last for 5 milliseconds, not 500.
The 555's output can be connected directly to the MOSFET gate, so
you can get rid of R1, R2, and the 1N4744.
Depending on the drive requirements of the MOSFET and how fast you want it to switch, you may have to switch to a bipolar 555.
Please post the data sheets - or links to their locations - for the solenoid, the MOSFET, and the flyback diode.
UPDATE:
Just for fun, here's your circuit redrawn so that it works, and simulated in LTspice:
Here are links to the files you'll need to run the sim. Download the files to the same folder, left-click on the .asc file to bring up the schematic and then left-click on the running man icon to start it.
Enjoy! :)
https://www.dropbox.com/s/avfi03sjc4h2e8n/AI555.asy?dl=0 https://www.dropbox.com/s/ip3rhu6qbllcpvj/Solenoid%20Driver.asc?dl=0
Best Answer
A common optocoupler has a current output: you connect the output transistor to Vcc and the emitter will source the current. How much depends on the CTR, or Current Transfer Ratio. That's not very much, and is usually expressed as a percentage. For instance a CTR of 30 % means that you need 10 mA input to get 3 mA output. Use those 3 mA to drive the base of a BJT. You'll want a Darlington to drive get more than 100 mA collector current.
But a Darlington has a high saturation voltage, and may take away too much from the solenoid's power supply voltage. A MOSFET may be better. But MOSFETs are voltage driven, not current driven like BJTs. So you have to convert the optocoupler's output current into a voltage. Nothing more easy: add a resistor between gate and ground, and the current through it will cause a voltage drop, which will turn on the FET.
The nice thing is that you can choose the voltage just by picking the right resistor value. For instance, our 3 mA will cause a 4.5 V gate voltage across a 1.5 kΩ resistor. You may be tempted to choose the resistor value rather high, but that's not necessarily a good idea. The optocoupler has a leakage current when off (called "dark current") and that will also cause a gate voltage. You'll have to make sure that won't get high enough to activate the FET. If the dark current is 10 µA ( a rather high value) then the 1.5 kΩ resistor will show 15 mV on the FET's gate, and that will be low enough not to switch it on. The 4.5 V from the 3 mA will be enough if you pick a logic level gate FET.
The LTV817 is a low-cost optocoupler which is perfect for this: minimum 50 % CTR, a dark current of only 100 nA, and a maximum collector-emitter voltage of 35 V.
Since the LTV817 has such a low dark current the value of R1 can be increased to 15 kΩ. Then 300 µA is enough to get the 4.5 V gate voltage, and the dark current will only cause a 1.5 V voltage across the resistor. At a 50 % CTR you'll only need 600 µA input current. Use 2 mA to have some margin.
For the FET there are plenty of options. The FDC855, for instance, will give you enough current at 4.5 V gate voltage, giving a negligible on-resistance of 36 mΩ: the voltage drop is only 24 mV, and the power dissipation 16 mW (that's 0.2 % of the solenoid's power).
Edit: Selecting the right FET
Like I said there are lots of FETs suitable for your application. I often refer to the FDC855 because it has a good balance between cost and features. For cost the rule is; the lower \$R_{DS(ON)}\$, the more expensive you FET. Yours has only to switch 0.67 A, that's average, and then an extremely low \$R_{DS(ON)}\$ (you can get them down to 1 mΩ) is not really necessary.
You found the PMF290XN cheap (though at Digikey it's only 25 % cheaper than the FDC855, not 80 %). It has a somewhat higher \$R_{DS(ON)}\$ of 350 mΩ, but that's still no problem. Voltage drop is 240 mV, and power dissipation 160 mW. That's more than the FDC855, but still OK.
The higher \$R_{DS(ON)}\$ also puts a limit to the current. For the PMF290XN that's 1 A, which isn't great, but enough for the application. The 2 A you read in the datasheet is pulsed (a single 10 µs pulse). Don't read it as 2 A continuous would be allowed, the 1 A is Absolute Maximum Rating. The (pulsed) higher currents just show where the graph is heading to.
Have a look at figures 6 and 7 also. Figure 6 shows that 3 V is sufficient for 1.5 A drain current, so more than enough for your 0.67 A. Figure 7 shows that you need 3.5 V for an \$R_{DS(ON)}\$ of 350 mΩ at 0.67 A.