- Not sure about exposure time (for my lamp).
- Not sure about UV light position and height required.
With these you just have to experiment, I'd suggest putting the board fairly close to the lamp (20-50mm or so).
I suggest you take one longish strip of photoresist PCB and put something on top of it that blocks UV light, then expose the strip while moving the UV blocker away at predefined intervals (say, every 10 seconds). What you will end up with is a PCB exposed in steps for different exposure times (10s, 20s, 30s, 40s, 50s etc.), then just pick the exposure time that gives off the best result.
- Not sure if my mask pattern is opaque enough (to UV light).
If it's a normal transparency sheet it should be fine. Printing to these with a laser printer works but this depends on your printer. Large areas of black might get overexposed but this depends on your printer. If your quality of black is bad you can print two sheets and align them on top of eachother.
- Not sure about correct proportions of caustic soda to water
I have been using a 3% solution of NaOH (KOH works too) which seems to work well.
- Not sure about time to leave the board in the caustic soda - whether I'm going too far developing.
You just basically move it around in the solution until it seems developed (black stuff comes off the board), usually it develops quite quickly (under 30s) but this depends on your solution. If your solution is too strong or you develop it too long it will strip off all the photoresist if you keep it in the solution too long. A solution not concentrated enough won't successfully develop the board (again, 3% solution seems to work well). Washing the board under a faucet afterwards works well. You can continue developing after taking it away from the solution. You can actually even continue developing after etching the board a bit, just remember to wash the board. Putting the board in the etching solution shows you pretty well where the board has photoresist and where it doesn't, the copper exposed to the etching solution goes to this "dull" color/texture in under a minute in the etching solution.
- I also dont know if a developed pre-sensitized board stays so, and wont fade as its left in daylight over time. How long before normal daylight affects a pre-sensitized developed board?
A board with the plastic shield SHOULDNT be affected by daylight but to be sure I'd keep them in a place shielded from light (like a drawer).
Btw. I'd suggest you try to expose your boards with a 11W fluorescent table lamp (the ones with a "U"-shaped lamp, they should be pretty common and cost like 10e from Ikea). Put the lamp quite close to the board (like 50mm close, and have a thin plate of glass over the board to keep the mask close to the board). You can get suitable plate of glass from picture frames (again, Ikea is a good place to get these), just make sure its real glass and not plastic. Expose for 12-15min (I've used 13,5min for my boards and setup). I have been using this method succesfully for a long time. Won't work for large boards due to the lamp being so narrow but for small boards it works well.
For tinning, my cheap home method is to coat the traces with a flux pen as soon as the board is finished etching, then run all over them with the thinnest coat of solder from my iron.
I've drilled them before and after the flux and or tin process and usually prefer to drill before fluxing.
I too use tin snips for cutting my boards, sometimes sanding the edges with 600 grit wet and dry paper with water and a little soap to get a nice smooth edge.
Conformal coating is available to coat and protect your board. I'm planning to give polyurethane varnish a try on my next project.
Best Answer
There are specific tools that are designed to cut holes in this material, which is either called "stripboard" or "veroboard". These tools are basically a drill bit in a moulded handle made of plastic or wood and look something like this:
(photo from here)
Because it is basically a drill bit you could use any high speed steel drill bit. There are some good instruction at Instructables that show how to cut neat holes. However if you plan on using stripboard often then it is worth buying a tool with a handle, they are quite inexpensive.