Interfacing pic184f450 with 16X2 lcd in four bit mode

I am working on interfacing 16X2 lcd in 4bit mode with pic18f4550.The higher 4 bits (D4,D5,D6,D7) are connected to PORTA1,A2,A3,A4 , pin RAO as RS, RE2 as RW, RE3 as RE3. i am struck with below code which displays nothing .The below code compiles without any error ,but display nothing (assume no mistake in my hardware connection)?
/*
* File: main.c
* Author: tamil
*
* Created on June 5, 2013, 11:32 PM
*/
#include

 #pragma config FOSC = HS  // to select external osc
// CPU System Clock Postscaler:
// [OSC1/OSC2 Src: /1][96 MHz PLL Src: /2 = 48 MHz CPU Clock]
#pragma config CPUDIV = OSC1_PLL2
#pragma config PWRT     = ON        // 62 ms waiting at start
#pragma config BOR      = ON        // Brown our Reset enabled (IMPORTANT!!!)
#pragma config BORV     = 2         // Reset level = 2,7 V
#pragma config WDT = OFF  // watch dog timer off
#pragma config DEBUG = ON,LVP = OFF // debugger on , as per pickit3
#pragma config PBADEN = OFF //PORTB<4:0> pins are configured as digital I/O on Reset
#pragma config MCLRE = ON //MCLR pin enabled; RE3 input pin disabled

//lvp should be off

 #define rs LATAbits.LATA0
 #define rw LATEbits.LATE1
 #define en LATEbits.LATE2
 #define lcdport LATA
    void Delay_ms(int ms)
 {
  int i,j=0;
   for(i=0;i<ms;i++)
    for(j=0;j<165;j++);

  }
       void lcdcmd(unsigned char cmdout)
     {
lcdport=(lcdport |(cmdout << 1));       //Send command to lcdport=PORTB
rs = 0;                     
rw = 0;
en = 1;
Delay_ms(1);
en = 0;
    }
       void lcddata(unsigned char dataout)
    {
lcdport=(lcdport | (dataout << 1)); //Send data to lcdport=PORTB
rs=1;
rw=0;
en=1;
Delay_ms(1);
en=0;
    }
   void dis_data(unsigned char data_value)
   {
unsigned char data_value1;
data_value1=(data_value&0xF0);
lcddata(data_value1);
data_value1=((data_value<<4)&0xF0);
lcddata(data_value1);
    }
    void dis_cmd(unsigned char cmd_value)
    {
unsigned char cmd_value1;
cmd_value1 = (cmd_value & 0xF0);    // Mask lower nibble because RB4-RB7 pins              are being used
lcdcmd(cmd_value1);         // Send to LCD
cmd_value1 = ((cmd_value<<4) & 0xF0);   // Shift 4-bit and mask
lcdcmd(cmd_value1);         // Send to LCD
    }
    void lcd_ini()
    {
dis_cmd(0x02);
    Delay_ms(200);// To initialize LCD in 4-bit mode.
dis_cmd(0x28);
    Delay_ms(200);// To initialize LCD in 2 lines, 5x7 dots and 4bit mode.
dis_cmd(0x0C);
    Delay_ms(200);
dis_cmd(0x06);
    Delay_ms(200);
dis_cmd(0x80);
    Delay_ms(200);
     }
   void main ()
     {
       unsigned char data[]="tamil";
       unsigned int x =8;
       //unsigned int y = 1;
        //unsigned int i=0;
           ADCON1=15; // to configure  all analog pins as digital i/o
           TRISA = 0; // to config port A as o/p
           TRISE = 0;// to make it as o/p
           lcd_ini();
           // LCD initialization

         while(data[i]!='\0')
       {
    dis_data(data[i]);
    Delay_ms(200);
    i++;
        }

}