Since I also have worked on the same type of displays, I must say that you are in the right direction.
But the thing is, connectors highly depend on the type of wires that are connected to both led strip and connector. Your wire must have enough gauge rating wire so that it would support such huge current. Here you can find what type of wires to use for your current consumption.
Once you select the kind of wire to use, the connectors can be chosen appropriately. This kind of connectors are simply ideal for situation. But I ended up using this type of connectors.
I must add that I have added the links to ebay. This does not mean that you must buy from it. I used that site just for the sake of pictures. Those kind of connectors are simply enough.
(1) Probable issue is attempt to massively over drive LEDs - see below.
Series LED resistors will be needed.
(2) Boost converter MAY be not working properly - see below for testing method.
LED datasheet here
TPS61201 boost converter datasheet here
Two x AA alkaline with provide a voltage between 3.2V and about 2V.
A larger value of C1 on Vin will do no harm and will help very low voltage/bad battery startup.
The TPS61201 boost converter will happily start and run on this voltage range.
The LEDs are NOT rated at 20 mA continuous - see data sheet.
LEDS are rated at
Also thermal limitations of IC must be observed.
Running LEDs directly off IC pins risks LED damage and possibly IC malfunction.
What is design requirement?:
Say 10 mA/LED and all on.
12 LEDS x 10 mA = 120 mA.
120 MA x 3V3 =~ 400 mW.
Efficiency at 120 mA out and 2V Vin ~= 75% - see fig4 from datasheet below.
So 400 mW/75% = 560 mW into converter.
At 2V Vin Iin = 560 mW/2V = 280 mA Iin.
This is well within IC capability.
So - IC is capable of providing requerement IF LEDs are correctly driven.
Problem may be excess LED drive OR bad converter components.
Test: Provide a 120 mA resistor load to converter.
R = V/I = 3.3 V / 120 mA = 27 Ohm.
Will converter supply 3V3 to 27 Ohm with 2V supply including startup?
Use lower R's for higher load current if desired.
If converter will not support desired load current then an inadequately rated inductor is the most likely problem.
Your Cout = 22 uF = 2 x data sheet value - should not be a problem. Sometimes high Cout can cause startup problems but 22 uF should be fine.
Most likely problem is massively high LED currents.
Add series resistors to set currents to 10 m max.
Note that Vf LED varies with colour - see datasheet.
ADDED:
New information:
LEDs are not as shown on diagram.
Assume max per LED current is 20 mA.
Actual LEDs are Dialight 5988710307F.
These LEDs are rated at 20 mA ABS MAX so you could run them at 20 mA, perhaps.
[Are you feeling lucky, punk?]
If so then double figures I supplied above to 1
20 mA x 12 = 240 mA.
This is still on the curve in Fig 4 above with 1.8V Vin so the converter can handle it.
TRY MY RESISTIVE LOAD TEST with R to suit real load.
If this passes OK then converter is OK.
If this fails then fix it first - chasing driver problems when the power supply is failing is liable to be unproductive :-).
ADDED:
A deleted answer suggested that rising battery impedance would mean that AA batteries could not be used in this application and that C or D cells were needed.
IMHO this is not true.
While AA cells will probably not reach full discharge potential due to falling current capability, they should work reasonably well.
The converter has a performance curve in fig 4 of the data sheet which shows operation at 1.8V = 0.9V/cell. As long as the batteries will provide the required load current at this voltage OR HIGHER the system will work OK.
At I_LED = 10 mA and all segments lit Ibattery at Vbattery=2V will be ABOUT 280 mA (see above) and at I_LED = 20 mA I_Battery at Vbattery = 2V will be about 550 mA (efficiency slightly HIGHER at higher load - see graph).
IF the battery is capable of providing about 500 mA at 2V+ then it will work. This is getting extreme for AA Alkaline but the battery will provide more power than this for much of its discharge life.
My simple resistor loading test will show whether the converter is OK at any given battery state.
Note that input capacitor matter muchly when batteries are near end of life. A large capacitor greatly reduces battery effective impedance on current peaks. Mean ESR is not altered but failures usually occur when current peaks occur during the boost cycle.
Best Answer
OK, let's round that to 100W.
One 3000mAh 18650 rated for 20A continuous current, as used in e-cigarettes, contains 11 Wh. With two, that's 22 Wh. With 100W power draw you cannot expect more than 15 minutes battery life. Factoring in converter losses, this will most likely be 10 minutes.
I assume you're okay with that, since you say "I need everything to fit in a cylinder of ~20mm". I assume you did your homework, and if you needed more than 10 minutes battery life, you would have specified an adequate size and weight for batteries. It is your problem.
For this level of current, you do not strictly need a multiphase buck converter, but it would make the job easier, use smaller inductors, reduce I2R losses... Ex-National Semiconductors has several chips which will do what you want.
Uhhh? What?
At high output currents, buck converters tend to have higher efficiencies. They are also easier on the batteries, since drawing power from a higher voltage source will require less current in the batteries.