I'm researching information on decoupling capacitors and came across some information about ferrite beads from TI:
Ferrite beads are very handy tools to have in your circuit design arsenal. They are, however, not a good idea for all circuit power rails.
Ferrite beads effectively absorb high frequency transients by raising their resistance at higher frequencies. This makes them very good at preventing power supply noise from getitng to sensitive circuit sections, however, it also makes them a very bad idea for main digital power.
When to use them:
Use them on power traces in series with analog circuit sections like composite video or PLLs. These beads effectively shut down power flow in times of high noise transients, allowing the power to be drawn only from the decoupling capacitors that are downstream. This cuts noise to sensitive circuit sections considerably.
How to use them:
Ferrite beads should be used in between two capacitors to ground. This forms a Pi filter and reduces the amount of noise to the supply considerably. In practice, the capacitor on the chip side should be placed as close to the chip supply ball as possible. The ferrite bead placement and input capacitor placement is not as crucial.
If there is not room for two capacitors to form a Pi filter, the next best thing is to delete the input capacitor. The chip side capacitor should always be there. This is very important. Otherwise the ferrite beads increased high frequency resistance may make things worse instead of better since there will be local power storage on the chip side, and therefore no way to get the high peak power pulses to the chip that it so desparately needs.
When not to use them:
The above ferrite traits are very handy for those circuit sections that draw power evenly and consistently, but the same traits make them unsuitable for digital power sections. Digital processors need high peak current, because most internal transistors that switch are switching on each clock edge, all the demand occurs at once. Ferrite beads (by definition) will not allow power to flow through them with the high ramp rates required by digital processor logic. This is what makes them perfect for noise filtering on analog (like PLL) supplies.
Since all the power demand in digital system is instant (high frequency), instead of being a slow and steady demand, ferrite beads will block the digital supply during the peaks. Theoretically, the bypass capacitors on the processor side of the bead would supply the peak current, filling in the gaps caused by the ferrites until they were charged after the peak was over, but in reality, the impedance of even the best capacitors is too high above about 200 MHz to supply enough peak power for the processor. In systems without ferrites, the planar capacitance can help to fill in this gap, but if a ferrite is used, it's inserted between the planes and the power pin, so the benefits of planar capacitance are lost. This will cause a big instantaneous voltage drop during the period the processor needs it most, causing logic errors and strange behavior if not immediate crashing. This can be avoided by proper design if required for your system (for EMI reduction, for example), however this is beyond the scope of this note.
I believe you should examine what your switching current spectrum looks like. If your digital circuits require large current transients, you should not use a ferrite bead on them.
I am currently of the mindset that the ferrite bead is useful in certain, very specific applications, but it is mostly used liberally as a band-aid when issues arise that should be solved by examining the power delivery network.
While it would be nice to see some graphs or other data, what I read here from TI sounds plausible. What do you guys think about it?
Best Answer
A large (330uF) capacitor between VDD,VSS is definitly worth doing but you should also investigate tweaking your OLED init code. Many OLED's have lots of config options to do with voltages and frequencies that can really make a difference to the amount of electrical noise they make by reducing their overall current draw but also by altering the "pattern" of said current draw.
I had the same problem as you with SSD1327 OLED from waveshare. The default configs work great but produced a significant amount of noise in my audio output. The main turned out to be the refresh rate that was well into the audible range at around 120Hz and much higher than actually necessary. A bit of tweaking to the internal oscillator config reduced the frame rate to a much lower value leading to less noise in the audible range. Futher tweaking to drive voltages reduced the scale of that noise so much that is almost unnoticable in my application.
I wrote more about it over on the EEVblog