Electronic – 24V supply run 12V 3014 LED strip in series; help with resistors for series

i need help with wiring up some pieces of a 12V LED strip in series to run on a 24V 150mA supply. i want to add resistors , to help keep the strings evenly balanced. i don’t know if it is necessary, especially because the ones in each LED series; But i don’t think so, from looking around the internet. i think it matters and i am not entirely sure why, but i think it keeps them even in power distribution, and hopefully keeps burn out from occurring as easily.

i am puzzled because i had found a video that said to use 20% more watts than your LED strip was rated. i don’t like that though.

i don’t know what it’s rated anyway , only
that the LED set is 3 regular 3014,

likely FM-3014WLS-460T-R80 (or the 70 CRI one FM-3014WLS-460R-R70 which has the same specs) from Nationstar (it’s the warm white LED strip )

~3 V (3.2 VF) 30 mA (35 mA max) in series with a 100 Ohm resistor (code on surface mount resistor on board is “101”)

each LED being a 0.1W diode? and a strip being 12V 0.1W if i understand correctly. so parallel (as they are in a strip) that looks like 1.8W on one strip in series with another 1.8W ; so, 18 LEDs (6 units of 3) on one strip in series with another 18 LEDs, but this is wrong, due to the resistor in every unit, and could maybe be approximate (but this isn’t the point of the question. i want to know) to 18/4 ~ 4.5 units so i guess, 4 units of 3 LEDs with a 100 Ohm resistor, is maybe 1.8 W / 16 things ~ 0.1125 W per thing, but that’s rubbish but also gives room to dump energy in the resistors before the positive and negative leads and maybe in between the LED strip, as they are linked in series ?

so i am asking for help in these calculations which are over my head, and to understand how to do them
(i would eventually love to learn about zener diodes, but this is a logical baby step, and i also don’t have any zener diodes 🙂

i am not sure if that will even work. for example, i have no clue what actual resistance each LED is giving, being that the range of volts and amps it is passing changes the resistance. (and i don’t have the volt and amp curve graph even if i could use that, the data sheet doesn’t include it or a wavelength efficiency chart)

so without that data there is only the 100 Ohms to use (unless i use 6 Ohm per LED for the heck of it because i saw it on a circuit lab LED value. but, assuming i didn’t ,

if a theoretical unit was set to 12 V , then V = I * R , 12 V= X * 100 Ohms, is 0.12 A which is high

, and V * I = W, 1.44 W for 3 LED and a 100 Ohm resistor.

i don’t know what i am getting wrong here right now.

a 0.1 LED would imply that 1.44 W – ( 3 * 0.1 W ) = 1.14 W of a resistor.

that doesn’t make sense; it’s way more energy than the LEDs. i must be doing something wrong.

i had figured that 3.2 V + 3.2 V + 3.2 V leaves 2.4 V to be filled by the resistor
and 3 V + 3 V + 3 V leaves 3 V to be filled by the resistor

i also tried to do with V = I * R for the resistor

one case :
2.4 V = 0.03 A * X (if LEDs at 30mA) , X = 80 Ohm => No
2.4 V = X * 100 Ohms , X = 0.024 A (24 mA)

second case :
3 V = 0.03 A * X , X = 100 Ohms
3 V = X * 100 Ohms , X = 0.03 A

it correlated with :

i had used an equation i found that said
I LED = [ V source – 3 * V LED ] / R
so,
I LED = [ 12 V – 3 * 3.2 V ] / 100 Ohms
I LED = 0.024 A
and
0.03 A = [ 12 V – 3X ] / 100 Ohms, X = 3 V
and even more disappointing was
.035 A = [ 12 V – 3X ] / 100 Ohms, X = 2.83333 V, which the curve that should have been on the datasheet would rule out.
the 100 Ohm resistor really seems to put a damper in everything , so i don’t know what further ones will do

But anyway, please help me understand the error of my calculations and lack of understanding.

thanks !