Electronic – arduino – Controling 4 LEDs with 5 pushbuttons and Arduino

arduinocledmicrocontrollerprogramming

My code:

#define MAX 50
const int LED1 = 2;
const int LED2 = 3;
const int LED3 = 4;
const int LED4 = 5;
int array[MAX];
int old_b = 0;
int val;
int counter = 0;
int i;
int temp;
int L1;
int L2;

void setup () {
  pinMode (A5, INPUT_PULLUP);
  Serial.begin(9600);
}

int readButtons (int pin) {
  int b, c;
  c = analogRead(pin);
  Serial.print("analogRead =  ");
  Serial.println(c);
  delay(100);
  if (c > 1015) b = 0;
  else if (c > 70 && c < 76) b = 1;
  else if (c > 122 && c < 128) b = 2;
  else if (c > 169 && c < 175) b = 3;
  else if (c > 209 && c < 217) b = 4;
  else if (c > 247 && c < 256) b = 5;
  else if (c > 280 && c < 291) b = 6;
  else b = 0;
  if (b == old_b) {
   return 0;
   old_b = b;
  } else {
    return b;
    old_b = b;              
    }                           
}

void loop () {
  while ((val = readButtons(5)) != 5) {
    if ((val == 1) || (val == 2) || (val == 3) || (val == 4)) {
      array[counter] = val;
      Serial.print("In  ");
      Serial.print(counter);                
      Serial.print(" saving ");            
      Serial.println(val);
      delay(200);
      counter++;
      if (counter == MAX) {
        counter = 0;
      } 
    }
  }

  temp = counter;
  counter = 0;

  for (i = 0; i < temp; i++) {
    if (array[i] % 2 == 0) {
      L1 = 2;
      L2 = array[i] / 3 + 3; 
    } else {
      L2 = 5;
      L1 = array[i] % 3 + 3;    
      }

    if (readButtons(5) != 5) {
     digitalWrite (L1, HIGH);
     if (readButtons(5) != 5) {
      digitalWrite (L2, HIGH);
      delay(1000);
      digitalWrite (L1, LOW);
      digitalWrite (L2, LOW);
      if (readButtons(5) == 5) {
        i = temp;
      }
     } else {
       digitalWrite (L1, LOW);
       i = temp; 
     }
    }

  }
}

So I have a function which detects if a button was pressed. Prior to that, I have determined in which range are values for certain button and all buttons are connected on analog pin 5 like this, except I have them 6 and my resistors have 2200 ohms. In the while () {...} loop, while the 5th button isn't pressed, Arduino is "looking" if any of first four buttons was pressed. If it was store it in an array and if not keep "looking". When 5th button is pressed, we brake out and store last known place in array in which value was stored and set the place counter to zero so when starting again, Arduino stores values in the first place of array. Then based on that what is stored I determine which pin/LED will light up. If at any time during blinking LEDs 5th button is pressed again, Arduino stops the blinking and again waits for the presses from first four buttons. That is how it is supposed to work in theory. In practice I still can't get it to stop blinking every time 5th button is pressed again. I have to press it multiple times, sometimes two or sometimes even more presses are necessary if I want it to stop blinking. I don't think using interrupts will help, since I don't know how I should implement them in my problem. Here is my circuit (except I have Arduino Duemilanove Atmega 168). LEDs go 1 to 4 from right to left:

Schematics

Best Answer

From your description, it seems you need to debounce the switch.

You can do this

Since you seem to be using some kind of resistive ladder to read multiple buttons on one ADC port, this will be a little more complicated.

Related Topic