eaglefreewarelayers
According the the Cadsoft website, Eagle Freeware supports '2 signal layers'. Am I right that Cadsoft includes power and ground layers in their definition of 'signal layers'?
In other words, am I right that Eagle Freeware doesn't support 2 signal layers, a ground layer and a power layer?
As Dave posted in his answer (+1), you need to enable the layers in the DRC. Here's an example:
And from the EAGLE help file (which is an excellent resource by the way):
Layers
The Layers tab defines which signal layers the board actually uses, how thick the copper and isolation layers are, and what kinds of vias can be placed (note that this applies only to actual vias; so even if no via from layer 1 to 16 has been defined in the layer setup, pads will always be allowed).
The layer setup is defined by the string in the "Setup" field. This string consists of a sequence of layer numbers, separated by one of the characters '*' or '+', where '*' stands for core material (also known as FR4 or something similar) and '+' stands for prepreg (or any other kind of isolation material). The actual core and prepreg sequence has no meaning to EAGLE other than varying the color in the layer display at the top left corner of this tab (the actual multilayer setup always needs to be worked out with the board manufacturer). The vias are defined by enclosing a sequence of layers with (...). So the setup string
(1*16)would mean a two layer board, using layers 1 and 16 and vias going through the entire board (this is also the default value). When building a multilayer board the setup could be something like
((1*2)+(15*16))which is a four layer board with layer pairs 1/2 and 15/16 built on core material and vias drilled through them, and finally the two layer pairs pressed together with prepreg between them, and vias drilled all the way through the entire board. Besides vias that go through an entire layer stack (which are commonly referred to as buried vias in case they have no connection to the Top and Bottom layer) there can also be vias that are not drilled all the way through a layer stack, but rather end at a layer inside that stack. Such vias are known as blind vias and are defined in the "Setup" string by enclosing a sequence of layers with [t:...:b], where t and b are the layers up to which that via will go from the top or bottom side, respectively. A possible setup with blind vias could be
[2:1+((2*3)+(14*15))+16:15]which is basically the previous example, with two additional outer layers that are connected to the next inner layers by blind vias. It is also possible to have only one of the t or b parameters, so for instance
[2:1+((2*3)+(15*16))]would also be a valid setup. Finally, blind vias are not limited to starting at the Top or Bottom layer, but may also be used in inner layer stacks, as in
[2:1+[3:2+(3*4)+5:4]+16:5]A blind via from layer a to layer b also implements all possible blind vias from layer a to all layers between layers a and b, so
[3:1+2+(3*16)]would allow blind vias from layer 1 to 2 as well as from 1 to 3.
Though @Samuel has already written what you need, here is a little more about the (EAGLE) internals.
PCBs are usually made of a resin reinforced by glass fibers. To make multi-layer PCBs, usually several thin double-layered PCBs (cores) are made and glued together by a so called prepeg. After this, the vias are drilled and the walls of the holes are coated by metal to make the vias conductive.
However, it's possible to add vias already to the cores and so to make vias between distinct layers. But this adds extra work / costs.
EAGLE allows to configure between which copper layers vias can be made in the LAYERS tab of the design rule window:
Here, two cores (green) are glued together by a prepeg (grey), and vias are possible through each core as well as the whole PCB. This is defined by the string ((1*2)+(15*16)) in the setup.
You can change it to (1*2*15*16) which also defines a four-layer PCB, but only with vias across the whole board.
Finally, you can of course your set up and use "1-16" vias only, and this is more for completeness.
Best Answer
The freeware version allows two layers, but what you use them for is up to you.
Obviously with only two layers, you have to mix power, ground and signal to some extent within those layers.
For projects requiring more than two layers, where having separate power and ground layers is applicable, you will want to consider paid versions instead.