Electronic – How do glass tube fuses work

Using the wrong type of eg 10 A fuse can result in death - and has done so in some cases.

As well as the aspects mentioned there is an extremely important characteristic of some fuses which Johny's answer was somewhat related to.

The characteristic is termed "high rupture capacity" or HRC. The rupture capacity or breaking current of a fuse is NOT directly rlated to its fusing current. The RC is the current that the fuse can interupt under fault conditions.

A fuse may be rated at say 10A bu an initial fault condition may produce an initial surge current of 100A, or 1000A or even 10,000A. If the fuse is unable to terminate this flowing current then "there will be problems".

Items like multimeters that are intended for mains use may have HRC fuses specified. This is because the mains will happily provide fault currents well in excess of their fusing currents. Currents of hundreds of amps can occur under mains fault conditions. Worst case, people have been killed because a non-HRC fuse was used when an HRC one was specified. An arc develops in the equipment, cannot be extinguished and the resultant arc energy melts and scatters the meter or other equipment essentially explosively.

While many HRC fuses are visibly special See Gargoyle mug shots HERE some appear nearly identical to standard small glass fuses. HRC fuses will almost invariably be ceramic rather than glass.

HRC fuse catalog - these are high voltage by normal standards, but it's interesting to note 3A fuses with 40,000A interruption capability.

Wikipedia - Fuses - breaking capacity

• The breaking capacity is the maximum current that can safely be interrupted by the fuse. Generally, this should be higher than the prospective short circuit current. Miniature fuses may have an interrupting rating only 10 times their rated current. Some fuses are designated High Rupture Capacity (HRC) and are usually filled with sand or a similar material. Fuses for small, low-voltage, usually residential, wiring systems are commonly rated, in North American practice, to interrupt 10,000 amperes. Fuses for larger power systems must have higher interrupting ratings, with some low-voltage current-limiting high interrupting fuses rated for 300,000 amperes. Fuses for high-voltage equipment, up to 115,000 volts, are rated by the total apparent power (megavolt-amperes, MVA) of the fault level on the circuit.

This Answers answer says

• The main advantage offered by an HRC fuse is that, when a fault current condition occurs, a tremendous amount of heat is created within the fuse. That heat melts the silica sand filling of the fuse into glass. Glass, being an insulator, suppresses any arc-over and breaks the circuit instantaneously. This behavior minimizes the possibility of a continuing - and dangerous - "high arc current" situation from developing, which is what happens if a normal fuse fails to break a heavy fault current.

  ... choosing to use an HRC fuse instead of a normal fuse makes very good sense if the equipment that needs to be protected - or other equipment nearby - would be very expensive to replace if it all went up in smoke just because of a fuse which was not capable of stopping a high fault current flowing.

  So, if some expensive electrical equipment was supplied with one or more HRC fuses installed to protect it, you would be very foolish indeed to replace them with normal "non-HRC" fuses.

Read more: http://wiki.answers.com/Q/What_is_the_advantage_of_an_HRC_high_rupturing_capacity_fuse#ixzz1uCKdwImw

If it is not exposed to the water, then it is used to make ozone and kill all airborne bacteria and virus and oxidize any organic compounds. It works fine for that and UV lamps are using in bio-labs and lots of places where they need to destroy organics.

There used to be mercury vapor lamps in clothes washers and they did not need the high voltage. Hardware stores some places may still have the replacement bulbs that fit a standard light bulb base.

It might have been meant to make ozone that diffuses into the water. But ozone lasts for a very short time in water. Despite this, there are a lot of people selling ozone generators to purify water that are of dubious efficacy.

The noisy part is a high voltage coil like a mini Tesla Coil. Some cement that holds the copper coils in place probably failed. They will buzz at the mains frequency if they get loose.