This doesn't answer your question, but might make the code a little easier for you to debug. The case statements are really long and may not be the best way to explain what you are doing with your outputs. I make no guarantees that the code is operational (I have not run it at all), but this should get you thinking about file size and readability.
Your singleminutes case statement has a truth table like this:
// | out
// in| 0 1 2 3 4
// ---------------
// 0 | 0 0 0 0 0
// 1 | 0 1 0 0 0
// 2 | 0 1 1 0 0
// 3 | 0 1 1 1 0
// 4 | 0 1 1 1 1
which might be better represented with output-centric code like this:
if (singleminutes >= 1)
PPEins = 1;
else
PPEins = 0;
if (singleminutes >= 2)
PPZwei = 1;
else
PPZwei = 0;
if (singleminutes >= 3)
PPDrei = 1;
else
PPDrei = 0;
if (singleminutes >= 4)
PPVier = 1;
else
PPVier = 0;
The nfminutes is a little more complicated, but here is the Truth Table:
// | MHUhr PMFuenf PMZehn PMViertel PMZwanzig PMVor PMNach PMHalb | |
// --|--------------------------------------------------------------|--------|-----
// 0 | 1 0 0 0 0 0 0 0 | 1000 0 | 000
// 1 | 0 1 0 0 0 0 1 0 | 0100 0 | 010
// 2 | 0 0 1 0 0 0 1 0 | 0010 0 | 010
// 3 | 0 0 0 1 0 0 1 0 | 0001 0 | 010
// 4 | 0 0 0 0 1 0 1 0 | 0000 1 | 010
// 5 | 0 1 0 0 0 1 0 1 | 0000 0 | 101
// 6 | 0 0 0 0 0 0 0 1 | 0000 0 | 001
// 7 | 0 1 0 0 0 0 1 1 | 0100 0 | 011
// 8 | 0 0 0 0 1 1 0 0 | 0000 1 | 100
// 9 | 0 0 0 1 0 1 0 0 | 0001 0 | 100
//10 | 0 0 1 0 0 1 0 0 | 0010 0 | 100
//11 | 0 1 0 0 0 1 0 0 | 0100 0 | 100
and again some output-centric code:
// MHUhr PMFuenf PMZehn PMViertel PMZwanzig
if( nfminutes == 0 )
MHUhr = 1;
else
MHUhr = 0;
if(( nfminutes == 1 ) || (nfminutes == 5) || (nfminutes == 7) || (nfminutes == 11))
PMFuenf = 1;
else
PMFuenf = 0;
if(( nfminutes == 2 ) || (nfminutes == 10) )
PMZehn = 1;
else
PMZehn = 0;
if(( nfminutes == 3 ) || (nfminutes == 9) )
PMViertel = 1;
else
PMViertel = 0;
if(( nfminutes == 4 ) || (nfminutes == 8) )
PMZwanzig = 1;
else
PMZwanzig = 0;
// PMVor PMNach PMHalb
if( ((nfminutes >= 1 ) && (nfminutes <= 4 )) || (nfminutes == 7))
PMNach = 1;
else
PMNach = 0;
if( (nfminutes >= 5) && (nfminutes <= 7 )
PMHalb = 1;
else
PMHalb = 0;
if(nfminutes >=8)
PMVor = 1;
else
PMVor = 0;
The code above might do well with some #defines too
#define UHR 0
#define PHUENF_NACH 1
#define ZEHN_NACH 2
...
if(nfminutes == UHR)
Again for hours. Truth Table:
| 12 1 2 3 4 5 6 7 8 9 10 11
//----|------------------------------------
// 0 | 1 0 0 0 0 0 0 0 0 0 0 0
// 1 | 0 1 0 0 0 0 0 0 0 0 0 0
// 2 | 0 0 1 0 0 0 0 0 0 0 0 0
// 3 | 0 0 0 1 0 0 0 0 0 0 0 0
// 4 | 0 0 0 0 1 0 0 0 0 0 0 0
// 5 | 0 0 0 0 0 1 0 0 0 0 0 0
// 6 | 0 0 0 0 0 0 1 0 0 0 0 0
// 7 | 0 0 0 0 0 0 0 1 0 0 0 0
// 8 | 0 0 0 0 0 0 0 0 1 0 0 0
// 9 | 0 0 0 0 0 0 0 0 0 1 0 0
// 10 | 0 0 0 0 0 0 0 0 0 0 1 0
// 11 | 0 0 0 0 0 0 0 0 0 0 0 1
and code. Slightly different structure with all outputs being cleared, then only the correct output turned on.
// one-hot, clear all will not cause a glitch
PHZwoelf = 0;
PHEins = 0;
PHZwei = 0;
PHDrei = 0;
PHVier = 0;
PHFuenf = 0;
PHSechs = 0;
PHSieben = 0;
PHAcht = 0;
PHNeun = 0;
PHZehn = 0;
PHElf = 0;
if( hours == 0 )
PHZwoelf = 1;
if( hours == 1 )
PHEins = 1;
if( hours == 2 )
PHZwei = 1;
if( hours == 3 )
PHDrei = 1;
if( hours == 4 )
PHVier = 1;
if( hours == 5 )
PHFuenf = 1;
if( hours == 6 )
PHSechs = 1;
if( hours == 7 )
PHSieben = 1;
if( hours == 8 )
PHAcht = 1;
if( hours == 9 )
PHNeun = 1;
if( hours == 10 )
PHZehn = 1;
if( hours == 11 )
PHElf = 1;
All this also allows you to do your input calculations together before your case statements.
// update single minutes
int singleminutes = (int) (unbcd(tm.min)%5); // 1, 2, 3, 4
// update 5 minutes
int nfminutes = (int) (unbcd(tm.min)/5); // Fuenf Nach, Zehn Nach, ...
// update hours
int hours = (int) (unbcd(tm.hour)%12); // 12, 1, 2, 3, 4...
if(nfminutes>=5) hours++; // 7:25 = Fuenf Vor Halb Acht (8)
Best Answer
Microchip's website has a document named Using the right Format, Syntax and Definitions for PICmicro Configuration Bits that explains where to find the configuration settings for your particular device.
For example it states for the PIC16F1 devices with a C Compiler:
If we look in the header file for your particular chip we find:
An example in the previously quoted document is:
Comparing this with the above header file you can see what each configuration macro will enable/disable.