- Not sure about exposure time (for my lamp).
- Not sure about UV light position and height required.
With these you just have to experiment, I'd suggest putting the board fairly close to the lamp (20-50mm or so).
I suggest you take one longish strip of photoresist PCB and put something on top of it that blocks UV light, then expose the strip while moving the UV blocker away at predefined intervals (say, every 10 seconds). What you will end up with is a PCB exposed in steps for different exposure times (10s, 20s, 30s, 40s, 50s etc.), then just pick the exposure time that gives off the best result.
- Not sure if my mask pattern is opaque enough (to UV light).
If it's a normal transparency sheet it should be fine. Printing to these with a laser printer works but this depends on your printer. Large areas of black might get overexposed but this depends on your printer. If your quality of black is bad you can print two sheets and align them on top of eachother.
- Not sure about correct proportions of caustic soda to water
I have been using a 3% solution of NaOH (KOH works too) which seems to work well.
- Not sure about time to leave the board in the caustic soda - whether I'm going too far developing.
You just basically move it around in the solution until it seems developed (black stuff comes off the board), usually it develops quite quickly (under 30s) but this depends on your solution. If your solution is too strong or you develop it too long it will strip off all the photoresist if you keep it in the solution too long. A solution not concentrated enough won't successfully develop the board (again, 3% solution seems to work well). Washing the board under a faucet afterwards works well. You can continue developing after taking it away from the solution. You can actually even continue developing after etching the board a bit, just remember to wash the board. Putting the board in the etching solution shows you pretty well where the board has photoresist and where it doesn't, the copper exposed to the etching solution goes to this "dull" color/texture in under a minute in the etching solution.
- I also dont know if a developed pre-sensitized board stays so, and wont fade as its left in daylight over time. How long before normal daylight affects a pre-sensitized developed board?
A board with the plastic shield SHOULDNT be affected by daylight but to be sure I'd keep them in a place shielded from light (like a drawer).
Btw. I'd suggest you try to expose your boards with a 11W fluorescent table lamp (the ones with a "U"-shaped lamp, they should be pretty common and cost like 10e from Ikea). Put the lamp quite close to the board (like 50mm close, and have a thin plate of glass over the board to keep the mask close to the board). You can get suitable plate of glass from picture frames (again, Ikea is a good place to get these), just make sure its real glass and not plastic. Expose for 12-15min (I've used 13,5min for my boards and setup). I have been using this method succesfully for a long time. Won't work for large boards due to the lamp being so narrow but for small boards it works well.
So from the previously linked answer,
I think the most
interesting/beneficial things for me
would be the bullet about learning the
tools (compiler and linker), and
learning different styles of software
architecture (going from interrupt
based control loops to schedulers and
RTOSes)
Porting a small operating system to a new device could help you to understand schedulers and RTOSs. FreeRTOS is popular and well documented. eCos is another.
Writing a bootloader is a good way to get to grips with a linker as you'll want to divide up memory and flash into regions.
Another tip is to pick a completely new architecture or chip and build yourself a development board. Forcing yourself to start right from the beginning and look everything up in the datasheet is a good way to learn.
Explore Protothreads. Try writing the same programs in both a threaded and state machine style. Once you're done with Protothreads, write a real thread scheduler.
Best Answer
many distributors offer a cross reference search.
For something as simple as a mosfet i would probably just go to digikey, head to the mosfet section and enter the parameters in the digikey search options from the datasheet of the part you have. Then compare datasheets for the results.