kicadpcbpcb-designschematics
I was designing new schematics and decided to inspect another library downloaded from kicad official sources on Github. The one thing that cought my eye instantly was that Electrical type for both GND and VCC was POWER INPUT.
Is it meant to be that way or just a workaround for an existing problem, eg. failing DRC?
There are a number of uncertainties in what you say you are doing. You need to stabilize the patient and understand what is really going on in order to make progress. At present there are several things wrong which are obscuring each other. Being able to deal with each ne in isolation makes life much easier.
(1) Your sentence below does not make sense. Can you please explain more clearly what you mean. "The MOSFETS are connected" and "drain and source ... connected" can both mean the same thing. If they DON'T mean the same you need to explain what you mean. You said:
(2) This would be fatal:
As Oli says, presumably you mean Vdd = Vcc. You need to read what you write before sending. We all need to and we all get it wrong sometimes BUT when you are asking the questions and want help then confusing the assembled masses with typos is a very bad idea.
(3) This probably means that your IC is dead or walking wounded OR you have a disconnected line - possibly ground. When things go this wrong you need to carefully measure everything - voltages when on and ohmic connections when off. look for shorts AND opens.
(4) If you were using "real" voltages your IC and random other things would now be dead. Shorting the capacitor connects the isolated high voltage "island" in thje IC to the drain of the lower FET which gets connected to ground when the lower FET is turned on. Shorting this cap could be an extremely exciting and non productive thing to do in many situations. Hopefully you determined before you did this what you expected to happen and didn't just do it to see what happened. When you are dealing with power rather than signal the magic smoke is never too far away. You may have had some already without being aware of it.
(5) Making the capacitor 100 times larger than you calculate in a circuit that may be switching at 10's to 100's of kHz is highly likely to produce interesting results. These could include an interesting emulation of lot's wife. But may not. The capacitor has to charge in the time that the low side FET is on. It discharges when the high side FET turns on. There will be charge & discharge time constants controlled by the resistance in the IC power paths. This may still work OK OR the voltages may only rise to a fraction of what is intended in the time available. Which may be consistent with what you are seeing.
I could add a bit more but that should do to start :-). Sometimes we all have a bad day - you need to try and not let too many things at once get out of control as then you can't asily analyse what is going wrong.
As others (and I) have suggested, measure everything you can and see if it makes sense. If you have an oscilloscope see what it can tell you. If you don't have a'scope, start putting lunch money aside for one. Even a relatively cheap scope can be a mightily powerful tool. An oscilloscope is possibly the most effective and powerful debugging and fault finding aid you will ever have for analog circuits.
Practical aspects:
If hand driving at low speed, connect Hin and Lin and SD low with pull down resistors. Then, if you hand switch them and they "bounce" they will bounce from low to applied signal level and not to some unknown state.
BUT the bootstrap powering circuit for the upper gate completely relies on there being an AC signal at VS to supply AC at Vb which draws power from Vcc and delivers it to Vb. If there is no AC your =upper gate signal will decay "rapidly". How long it takes depends on upper driver power consumption and was part of your capacitor calculations (from memory). This is an example of where an oscilloscope will help you see what is happening. The 100 uF you are using is a large value and decay time may be long enough to see what is happening "by eye", but maybe not.
If you want to drive with a microcontroller you could reduce Vcc to Vdd rather than raising Vcc - as long as IC minimum voltage spec is still met.
Re-etch of PCB MAY be a good idea BUT you should be able to carefully go over circuit and check that what you have is what you intend. Do it pin by pin.Talking to yourself about it as you go can help :-) (really). Describe what you expect to see and what you really see and why they are or aren't compatible. [Watch for men in white coats observing you suspiciously when you are talking to yourself - or do it in your head or, works well, get a knowledgeable friend and explain it to them. The very act of explaining often works wonders.]
The Electrical Rule Check executes, depending on the pin direction (specified by the author of the schematic symbol), various checks. It expects for the direction of type Pwr a Sup pin set for this net. Sup is a pin type for power supply outputs for ground and supply symbols.
From the Eagle manual:
"[...] For every Pwr-pin there must be at least one pin with the same name but the direction Sup(a supply pin). There must be one on every sheet. These Sup pins are fetched into the schematic in the form of power supply symbols, and are defined as Devices in a library (see supply*.lbr). These Devices do not have a Package, since they do not represent components. [...]"
Further...
"If there is no supply pin in the supply libraries that fits to your voltage in the schematic, you have to define a new supply pin! Renaming an already existing supply pin is the wrong way and can lead to unexpected results!"
Best Answer
VCC and GND are meant to be power inputs. ERC on the schematic will check that all power inputs are driven i.e. have a power output somewhere on the net. It'll also make sure you don't connect two power outputs together. An example of a power output would be the output terminal of a regulator.
The idea starts to break down if you put passives (inductors, chokes, resistors) that break up the net, but it can be helpful when used properly.