Here is the configuration:
Current configuration : 154 bytes
!
interface Port-channel1
description TRUNK
switchport trunk allowed vlan 10,20
switchport mode trunk
end
interface GigabitEthernet1/0/47
description SW1
switchport trunk allowed vlan 10,20
switchport mode trunk
speed 1000
duplex full
channel-protocol lacp
channel-group 1 mode active
end
interface GigabitEthernet1/0/48
description SW1
switchport trunk allowed vlan 10,20
switchport mode trunk
speed 1000
duplex full
channel-protocol lacp
channel-group 1 mode active
end
I have verified and other side of switch has same configuration. i have matched them word to word.
Here is the etherchannel summary
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
1 Po1(SU) LACP Gi1/0/47(P) Gi1/0/48(s)
On switch port i have seen Amber light
In log i have seen:
Feb 28 22:39:45.558: %EC-5-L3DONTBNDL2: Gi1/0/48 suspended: LACP currently not enabled on the remote port.
etherchannel details:
#sh etherchannel 1 detail
Group state = L2
Ports: 2 Maxports = 16
Port-channels: 1 Max Port-channels = 16
Protocol: LACP
Minimum Links: 0
Ports in the group:
-------------------
Port: Gi1/0/47
------------
Port state = Up Mstr Assoc In-Bndl
Channel group = 1 Mode = Active Gcchange = -
Port-channel = Po1 GC = - Pseudo port-channel = Po1
Port index = 0 Load = 0x00 Protocol = LACP
Flags: S - Device is sending Slow LACPDUs F - Device is sending fast LACPDUs.
A - Device is in active mode. P - Device is in passive mode.
Local information:
LACP port Admin Oper Port Port
Port Flags State Priority Key Key Number State
Gi1/0/47 SA bndl 32768 0x1 0x1 0x130 0x3D
Partner's information:
LACP port Admin Oper Port Port
Port Flags Priority Dev ID Age key Key Number State
Gi1/0/47 SA 32768 6c99.8962.2900 0s 0x0 0x10 0x110 0x3D
Age of the port in the current state: 1d:17h:22m:19s
Port: Gi1/0/48
------------
Port state = Up Cnt-bndl-rmt Suspend Mstr Rmt-LACP_Dsbl Not-in-Bndl
Channel group = 1 Mode = Active Gcchange = -
Port-channel = null GC = - Pseudo port-channel = Po1
Port index = 0 Load = 0x00 Protocol = LACP
Flags: S - Device is sending Slow LACPDUs F - Device is sending fast LACPDUs.
A - Device is in active mode. P - Device is in passive mode.
Local information:
LACP port Admin Oper Port Port
Port Flags State Priority Key Key Number State
Gi1/0/48 SA susp 32768 0x1 0x1 0x131 0x7D
Age of the port in the current state: 0d:00h:28m:16s
Port-channels in the group:
---------------------------
Port-channel: Po1 (Primary Aggregator)
------------
Age of the Port-channel = 1d:17h:26m:42s
Logical slot/port = 9/1 Number of ports = 1
HotStandBy port = null
Port state = Port-channel Ag-Inuse
Protocol = LACP
Port security = Disabled
Ports in the Port-channel:
Index Load Port EC state No of bits
------+------+------+------------------+-----------
0 00 Gi1/0/47 Active 0
Time since last port bundled: 1d:17h:22m:19s Gi1/0/47
Otherside switch SW1
i am seeing this.
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
16 Po16(SU) LACP Gi1/0/14(D) Gi1/0/15(P)
interface status:
SW1#sh int Gi1/0/14
GigabitEthernet1/0/14 is down, line protocol is down (notconnect)
Best Answer
This often happens when you connect to an interface that doesn't have LACP enabled, as you have discovered. Using CDP or LLDP will tell you for sure what the interface on the other end is, assuming you have one of those enabled on both devices.