I have two routers connected to a single switch and both have internet connections. I have configured HSRP and VRRP as follows, This is a test bench I'm using so that's why I'm using both. The HSRP is working as normal on the GigabitEthernet 0/1 interface, but on the vlans they are both active. Here are the configs:
Cisco Router 1
interface GigabitEthernet0/0
ip address 10.21.6.10 255.255.255.0
ip nat outside
exit
interface GigabitEthernet0/1
ip address 192.168.1.2 255.255.255.0
standby 0 ip 192.168.1.1
standby 0 priority 95
standby 0 preempt
ip nat inside
interface GigabitEthernet0/1.101
encapsulation dot1Q 101
ip address 192.168.101.2 255.255.255.240
vrrp 1 ip 192.168.101.1
vrrp 1 priority 95
ip nat inside
interface GigabitEthernet0/1.102
encapsulation dot1Q 102
ip address 192.168.102.2 255.255.255.0
standby 2 ip 192.168.102.1
standby 2 preempt
ip nat inside
interface GigabitEthernet0/1.103
encapsulation dot1Q 103
ip address 192.168.103.2 255.255.255.0
vrrp 3 ip 192.168.103.1
vrrp 3 priority 140
ip nat inside
interface GigabitEthernet0/1.104
encapsulation dot1Q 104
ip address 192.168.104.2 255.255.255.0
standby 4 ip 192.168.104.1
standby 4 priority 95
standby 4 preempt
ip nat inside
interface GigabitEthernet0/1.105
encapsulation dot1Q 105
ip address 192.168.105.2 255.255.255.0
vrrp 5 ip 192.168.105.1
vrrp 5 priority 95
ip nat inside
interface GigabitEthernet0/1.106
encapsulation dot1Q 106
ip address 192.168.106.2 255.255.255.0
standby 6 ip 192.168.106.1
standby 6 preempt
ip nat inside
interface GigabitEthernet0/1.107
encapsulation dot1Q 107
ip address 192.168.107.2 255.255.255.192
vrrp 7 ip 192.168.107.1
vrrp 7 priority 140
ip nat inside
interface GigabitEthernet0/1.108
encapsulation dot1Q 108
ip address 192.168.108.2 255.255.255.192
standby 8 ip 192.168.108.1
standby 8 priority 95
standby 8 preempt
ip nat inside
interface GigabitEthernet0/1.109
encapsulation dot1Q 109
ip address 192.168.109.2 255.255.255.0
vrrp 9 ip 192.168.109.1
vrrp 9 priority 95
ip nat inside
Router 2
int g0/0
ip address 10.21.6.11 255.255.255.0
ip nat outside
no shutdown
exit
int g0/1
ip address 192.168.1.3 255.255.255.0
standby 0 ip 192.168.1.1
standby 0 preempt
ip nat inside
no shutdown
exit
int g0/1.101
encapsulation dot1Q 101
ip address 192.168.101.3 255.255.255.240
vrrp 1 ip 192.168.101.1
vrrp 1 priority 140
ip nat inside
exit
int g0/1.102
encapsulation dot1Q 102
ip address 192.168.102.3 255.255.255.0
standby 2 ip 192.168.102.1
standby 2 priority 95
standby 2 preempt
ip nat inside
exit
int g0/1.103
encapsulation dot1Q 103
ip address 192.168.103.3 255.255.255.0
vrrp 3 ip 192.168.103.1
vrrp 3 priority 95
ip nat inside
exit
int g0/1.104
encapsulation dot1Q 104
ip address 192.168.104.3 255.255.255.0
standby 4 ip 192.168.104.1
standby 4 preempt
ip nat inside
exit
int g0/1.105
encapsulation dot1Q 105
ip address 192.168.105.3 255.255.255.0
vrrp 5 ip 192.168.105.1
vrrp 5 priority 140
ip nat inside
exit
int g0/1.106
encapsulation dot1Q 106
ip address 192.168.106.3 255.255.255.0
standby 6 ip 192.168.106.1
standby 6 priority 95
standby 6 preempt
ip nat inside
exit
int g0/1.107
encapsulation dot1Q 107
ip address 192.168.107.3 255.255.255.192
vrrp 7 ip 192.168.107.1
vrrp 7 priority 95
ip nat inside
exit
int g0/1.108
encapsulation dot1Q 108
ip address 192.168.108.3 255.255.255.192
standby 8 ip 192.168.108.1
standby 8 preempt
ip nat inside
exit
int g0/1.109
encapsulation dot1Q 109
ip address 192.168.109.3 255.255.255.0
vrrp 9 ip 192.168.109.1
vrrp 9 priority 140
ip nat inside
exit
Does anyone have any idea on why it would be doing this.
Best Answer
I found the problem, my team member had set that port to receive monitor traffic and therefor it was not trunking any vlan traffic to the router. Once this was fixed everything started working. thanks @RonTrunk