The routers on a stick are running VRRP on g0/0.10, g0/0.20 and g0/0.30.
On switches, ports fa0/1-8 are on VLAN 10, fa0/23 and fa0/24 are configured as trunk port, with allowed VLANs 10, 20 and 30.
Show VRRP on HQ2 shows that all VRRP are as master, but on HQ1, they show as init, router are 2900 running IOS 15.1 and switch are 3560 running IOS 12.2,
I had the router on a stick running on 1 router and 1 switch with no problem and also VRRP running on a single switch with no problem, but there is something I do not understand here! there is no other config on router and switches.
address on HQ2 have been change to x.x.x.253.
config HQ1
HQ1>show run
^
% Invalid input detected at '^' marker.
HQ1>ena
Current configuration : 1712 bytes
version 15.4
hostname HQ1
ip cef
redundancy
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
interface GigabitEthernet0/0.10
encapsulation dot1Q 10
ip address 192.168.222.254 255.255.255.0
vrrp 1 ip 192.168.222.100
interface GigabitEthernet0/0.20
encapsulation dot1Q 20
ip address 192.168.223.254 255.255.255.0
vrrp 2 ip 192.168.223.100
interface GigabitEthernet0/0.30
encapsulation dot1Q 30 native
ip address 192.168.224.254 255.255.255.0
vrrp 3 ip 192.168.224.100
interface GigabitEthernet0/1
ip address 200.100.0.14 255.255.255.252
duplex auto
speed auto
interface Serial0/0/0
ip address 10.1.1.1 255.255.255.252
clock rate 2000000
Configuration on the other router is the same except that address for g0/0.10 .20 and .30 terminate with 253 instead of 254 and of course the address for the serial connection is different. also discover a bad port on the switch so both VRRP are saying master now, so they do not communicate.
HQ1(config-subif)#do show vrrp
GigabitEthernet0/0.10 - Group 1
State is Backup
Virtual IP address is 192.168.222.100
Virtual MAC address is 0000.5e00.0101
Advertisement interval is 1.000 sec
Preemption enabled
Priority is 100
Master Router is 192.168.222.253, priority is 150
Master Advertisement interval is 1.000 sec
Master Down interval is 3.609 sec (expires in 3.369 sec)
GigabitEthernet0/0.20 - Group 2
State is Backup
Virtual IP address is 192.168.223.100
Virtual MAC address is 0000.5e00.0102
Advertisement interval is 1.000 sec
Preemption enabled
Priority is 100
Master Router is 192.168.223.253, priority is 150
Master Advertisement interval is 1.000 sec
Master Down interval is 3.609 sec (expires in 3.153 sec)
GigabitEthernet0/0.30 - Group 3
State is Master
Virtual IP address is 192.168.224.100
Virtual MAC address is 0000.5e00.0103
Advertisement interval is 1.000 sec
Preemption enabled
Priority is 100
Master Router is 192.168.224.254 (local), priority is 100
Master Advertisement interval is 1.000 sec
Master Down interval is 3.609 sec
HQ2#show vrrp
GigabitEthernet0/0.10 - Group 1
State is Master
Virtual IP address is 192.168.222.100
Virtual MAC address is 0000.5e00.0101
Advertisement interval is 1.000 sec
Preemption enabled
Priority is 150
Master Router is 192.168.222.253 (local), priority is 150
Master Advertisement interval is 1.000 sec
Master Down interval is 3.414 sec
GigabitEthernet0/0.20 - Group 2
State is Master
Virtual IP address is 192.168.223.100
Virtual MAC address is 0000.5e00.0102
Advertisement interval is 1.000 sec
Preemption enabled
Priority is 150
Master Router is 192.168.223.253 (local), priority is 150
Master Advertisement interval is 1.000 sec
Master Down interval is 3.414 sec
GigabitEthernet0/0.30 - Group 3
State is Master
Virtual IP address is 192.168.224.100
Virtual MAC address is 0000.5e00.0103
Advertisement interval is 1.000 sec
Preemption enabled
Priority is 150
Master Router is 192.168.224.253 (local), priority is 150
Master Advertisement interval is 1.000 sec
Master Down interval is 3.414 sec
Best Answer
OK, I found the problem, for some reason erasing the startup-config did not really erased everything, So I went in rommon and reset HQ2 to factory default and it is working.