3ware: Add a drive to a RAID unit

3wareraid

I have a 3ware RAID controller running a RAID-6. I manage the RAID via the tw_cli command line utility.

So, one drive in the array failed, and I removed the faulty drive (p6) from the array, and then inserted a new drive.

For some reason, the 3ware controller placed the drive in an older, inoperable array (u1). So I deleted that array. I now want to add the new drive to the RAID-6, which is u0.

So I have:

# tw_cli /c0/u0 show

Unit     UnitType  Status         %RCmpl  %V/I/M  VPort Stripe  Size(GB)
------------------------------------------------------------------------
u0       RAID-6    DEGRADED       -       -       -     256K    2793.91   
u0-0     DISK      OK             -       -       p0    -       465.651   
u0-1     DISK      OK             -       -       p1    -       465.651   
u0-2     DISK      OK             -       -       p2    -       465.651   
u0-3     DISK      OK             -       -       p3    -       465.651   
u0-4     DISK      OK             -       -       p4    -       465.651   
u0-5     DISK      OK             -       -       p5    -       465.651   
u0-6     DISK      DEGRADED       -       -       -     -       465.651   
u0-7     DISK      OK             -       -       p7    -       465.651   
u0/v0    Volume    -              -       -       -     -       10        
u0/v1    Volume    -              -       -       -     -       2783.91

As you can see, drive p6 is not part of u0. However, it is detected by the controller:

# tw_cli /c0 show

Unit  UnitType  Status         %RCmpl  %V/I/M  Stripe  Size(GB)  Cache  AVrfy
------------------------------------------------------------------------------
u0    RAID-6    DEGRADED       -       -       256K    2793.91   RiW    OFF    

VPort Status         Unit Size      Type  Phy Encl-Slot    Model
------------------------------------------------------------------------------
p0    OK             u0   465.76 GB SATA  0   -            ST3500630AS         
p1    OK             u0   465.76 GB SATA  1   -            ST3500630AS         
p2    OK             u0   465.76 GB SATA  2   -            ST3500630AS         
p3    OK             u0   465.76 GB SATA  3   -            ST3500320AS         
p4    OK             u0   465.76 GB SATA  4   -            ST3500630AS         
p5    OK             u0   465.76 GB SATA  5   -            ST3500630AS         
p6    OK             -    465.76 GB SATA  6   -            ST3500320AS         
p7    OK             u0   465.76 GB SATA  7   -            ST3500630AS         

Name  OnlineState  BBUReady  Status    Volt     Temp     Hours  LastCapTest
---------------------------------------------------------------------------
bbu   On           Yes       OK        OK       OK       0      xx-xxx-xxxx

So here we see that p6 is detected by the controller, but it is not part of the unit u0. So I just need to add it somehow. Unfortunately, I cannot find the syntax to do this.

Looking through the tw_cli docs, there doesn't seem to be a unit-level command to add a drive to a unit. So, how do you add a drive to a unit? How can I make p6 part of u0?

Best Answer

Hmm, I agree, it's vague. I've always worked with spares, so drives are added automatically. Perhaps you can hack that too:

tw_cli /c0 add raidtype=spare disk=6

Then perhaps it will pick it up automatically.

Related Topic