Cisco ASA ssh portforwarding with custom port

ciscocisco-asanat;

Cisco ASA 8.4(1)
ADSM 6.4

I'm struggling with forwarding SSH connections from the outside into a server inside my network on a non standard port.

What would the command line look like if I wanted to forward port 2828 from the outside to port 22 on a specific IP on the inside ?

Update: Provide config, started out with setting the standard SSH port on the outside since I cant get the above to work.

    : Saved
:
ASA Version 8.4(1) 
!
hostname troll
enable password XXXXXXX encrypted
passwd XXXXXXX encrypted
multicast-routing
names
!
interface Vlan1
 nameif inside
 security-level 100
 ip address 192.168.1.1 255.255.255.0 
!
interface Vlan2
 mac-address 0022.6b6e.4165
 nameif outside
 security-level 0
 ip address dhcp 
!
interface Ethernet0/0
 switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
dns domain-lookup inside
dns server-group DefaultDNS
 name-server 8.8.8.8
 name-server 8.8.4.4
same-security-traffic permit inter-interface
object network obj_any 
 subnet 0.0.0.0 0.0.0.0
object network outside 
 host 10.10.10.0
 description outside 
object network vm 
object network inside-host-object 
 host 192.168.1.100
access-list outside_access_in extended permit tcp any object inside-host-object eq ssh 
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic any interface
!
object network inside-host-object
 nat (inside,outside) static interface service tcp ssh 2828 
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 10.10.10.0 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
console timeout 0

dhcp-client client-id interface outside
dhcpd auto_config outside
!
dhcpd address 192.168.1.9-192.168.1.40 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
!
class-map inspection_default
 match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
 parameters
  message-length maximum client auto
  message-length maximum 512
policy-map global_policy
 class inspection_default
  inspect dns preset_dns_map 
  inspect ftp 
  inspect h323 h225 
  inspect h323 ras 
  inspect rsh 
  inspect rtsp 
  inspect esmtp 
  inspect sqlnet 
  inspect skinny  
  inspect sunrpc 
  inspect xdmcp 
  inspect sip  
  inspect netbios 
  inspect tftp 
  inspect ip-options 
!
service-policy global_policy global
prompt hostname context 
: end
no asdm history enable

Best Answer

You'll be configuring this in a network object defined for your inside host. If you already have one, you'll need to make the appropriate changes to it.

object network inside-host-object
 ! 192.0.2.1 is your internal address for this server..
 host 192.0.2.1
 ! ..and 203.0.113.1 is the external address that you want to use.
 nat (inside,outside) static 203.0.113.1 service tcp 22 2828

And you'll also need to make sure that the traffic is allowed in the outside interface's ACL - allow the traffic based on the post-NAT IP and port (so, in this example, a destination of 192.0.2.1, port 22), which is a change from older ASA behavior.

Related Topic