The interface on the JD990A is very cut down. There is a serial console with minimal commands and a web interface.
The 3750 is in a 2 switch stack and I am trying to configure cross-stack link aggregation with the HP. Most information online tends towards a better HP switch with cli access this does not have.
Does anyone have any idea what may be required to achieve this?
Cisco 3750: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9NPE-M), Version 15.0(2)SE2, RELEASE SOFTWARE (fc1)
HP JD990A: Software Ver: 02.00.01
Cisco 3750 Config
!
! Last configuration change at 01:50:10 AEST Thu Jun 13 2013 by administrator
! NVRAM config last updated at 01:50:11 AEST Thu Jun 13 2013 by administrator
!
version 15.0
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service sequence-numbers
!
hostname 1.c.s.net
!
boot-start-marker
boot-end-marker
!
!
enable secret 5 redacted
!
username administrator privilege 15 secret 5 redacted
aaa new-model
!
!
aaa authentication login default local
aaa authorization exec default local
!
!
!
!
!
!
aaa session-id common
clock timezone redacted
switch 1 provision ws-c3750x-24
switch 2 provision ws-c3750x-24
system mtu routing 1500
!
!
!
ip domain-name corp.redacted.com.au
!
stack-power stack PowerStack-1
!
!
!
crypto pki trustpoint TP-self-signed-3311124608
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3311124608
revocation-check none
rsakeypair TP-self-signed-3311124608
!
!
crypto pki certificate chain TP-self-signed-3311124608
certificate self-signed 01
redacted
quit
cts server deadtime 0
no cts server test all enable
cts server test all idle-time 0
cts server test all deadtime 0
!
!
!
spanning-tree extend system-id
!
!
!
!
!
!
vlan internal allocation policy ascending
!
ip scp server enable
!
!
!
!
!
interface Port-channel5
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast trunk
!
interface FastEthernet0
no ip address
!
interface GigabitEthernet1/0/1
!
interface GigabitEthernet1/0/2
!
interface GigabitEthernet1/0/3
!
interface GigabitEthernet1/0/4
!
interface GigabitEthernet1/0/5
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast trunk
channel-protocol lacp
channel-group 5 mode active
!
interface GigabitEthernet1/0/6
!
interface GigabitEthernet1/0/7
!
interface GigabitEthernet1/0/8
!
interface GigabitEthernet2/0/1
!
interface GigabitEthernet2/0/2
!
interface GigabitEthernet2/0/3
!
interface GigabitEthernet2/0/4
!
interface GigabitEthernet2/0/5
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast trunk
channel-protocol lacp
channel-group 5 mode active
!
interface GigabitEthernet2/0/6
!
interface GigabitEthernet2/0/7
!
interface GigabitEthernet2/0/8
!
interface Vlan1
ip address 10.1.1.242 255.255.255.0
!
ip http server
ip http secure-server
!
!
!
!
line con 0
logging synchronous
line vty 0
exec-timeout 0 0
transport input ssh
transport output ssh
line vty 1 4
line vty 5 15
!
ntp server 10.1.1.21 prefer
end
Best Answer
NOTE: I'm posting this as an answer mainly because a comment was very hard to read. I'm not certain if you are asking how to configure the HP switch or if you want full details on both sides (cisco and HP).
The JD990A is the HP 1905, right? The 3COM OfficeConnect acquisition line?
See these two links:
http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/c02581623/c02581623.pdf
http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/c02583125/c02583125.pdf
You should be able to configure LACP on the ports through the web interface of the HP switch to correspond with the LACP config on the ports on the Cisco switch.
Just be sure that you configure the HP side aggregation type as LACP instead of static.