It is unclear whether you want topology A or B below (I think you need B, but your question seems to ask for A)
Vlan10 Vlan10
A) [Users]----------[EX330]----------[ISP]
x.x.x.x/zz
Vlan10 Vlan11
B) [Users]----------[EX330]---------------------------[ISP]
y.y.y.y/24 xx.xx.xx.109/30 .110/30
A)
This is a flat layer2 vlan, and all your computers must be addressed on a subnet from the ISP. Vlan-10 is used for all your machines and they set their default-gateway to x.x.x.x.
I'm not sure why you're using a /32 mask in your question. It's unlikely that you want to do this, since it means you proxy-arp for all destinations. Work with your provider to understand what your actual netmask should be (I'm assuming zz, below)
delete interfaces ge-0/1/0 unit 0
delete interfaces ge-0/1/0
delete interfaces ge-0/1/1 unit 0
delete interfaces ge-0/1/1
set vlans vlan-10 vlan-id 10
set vlans vlan-10 interface ge-0/1/0
set vlans vlan-10 interface ge-0/1/1
set interfaces ge-0/1/0 unit 0 family ethernet-switching port-mode access
set interfaces ge-0/1/1 unit 0 family ethernet-switching port-mode access
set interfaces vlan unit 10 family inet address x.x.x.x/zz
set routing-options static route 0.0.0.0/0 next-hop xx.xx.xx.110
B)
This involves two different vlans: 10 and 11. Vlan-10 is used for all your servers and they set their default-gateway to y.y.y.y.
delete interfaces ge-0/1/0 unit 0
delete interfaces ge-0/1/0
delete interfaces ge-0/1/1 unit 0
delete interfaces ge-0/1/1
set vlans vlan-10 vlan-id 10
set vlans vlan-11 vlan-id 11
set vlans vlan-10 interface ge-0/1/0
set vlans vlan-11 interface ge-0/1/1
set interfaces ge-0/1/0 unit 0 family ethernet-switching port-mode access
set interfaces ge-0/1/1 unit 0 family ethernet-switching port-mode access
set interfaces vlan unit 11 family inet address xx.xx.xx.109/30
set interfaces vlan unit 10 family inet address y.y.y.y/zz
set routing-options static route 0.0.0.0/0 next-hop xx.xx.xx.110
Add as many ports as you need for servers in Vlan-11. Solution B must use some form of NAT if you don't have enough public address space from your provider to include both subnets for Vlan10 and Vlan11
Let's keep this straight here...
192.168.110.0/24 via VLAN.0 interface, okay, fine, you should have a bunch of ports configured as family ethernet-switching, wiht no vlan set, since this appears to be the default vlan.
Now... you've configured ge-0/0/6.0 as family inet, with the IP address 192.168.111.1/24. That interface should go to your existing gear, which will also need an interface on 192.168.111.0/24, let's say 192.168.111.2/24.
So, your static route on your SRX should be.... 192.168.1.0/24 next-hop 192.168.111.2. On the OTHER side... you will also need a static route, 192.168.110.0/24 next-hop 192.168.111.1.
Got it? When using static routes, you need them on the gear on both sides.
Best Answer
Because this is an SRX, there are a number of requirements here.
Step 1:
Define VLANS (think layer 2)
Step 2:
Define L3 interfaces bound to those vlans...
Step 3:
Place those L3 interfaces into a zone
Step 4:
Since this is an SRX, you must create a policy permitting intra-zone traffic
Step 5:
Set physical interfaces onto that VLAN
Step 6:
Plug devices in. Once any interface assigned to that VLAN is physically up, the VLAN interface for that VLAN will come up.