Linux – LVS-TUN: ifconfig shows errors and collisions for tunl0 interface

ifconfiglinuxnetworking

Check_MK has sent me an email as follows:

***** Nagios *****

Notification Type: PROBLEM

Service: Interface 5
Host: foo
Address: x.y.z.t
State: CRITICAL

Date/Time: Fri May 3 10:02:40 ICT 2013

Additional Info: CRIT - [tunl0] (up) speed unknown, in: 3.39MB/s, out: 0.00B/s, out-errors: 100.00%(!!) = 0.1

Running ifconfig, I got:

tunl0     Link encap:IPIP Tunnel  HWaddr   
          inet addr:x.y.z.t  Mask:255.255.255.255
          UP RUNNING NOARP  MTU:1480  Metric:1
          RX packets:92101704629 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:652 dropped:0 overruns:0 carrier:0
          collisions:652 txqueuelen:0 
          RX bytes:18941091817671 (17.2 TiB)  TX bytes:0 (0.0 b)

Pay attention to the errors and collisions. I know that a nonzero value of the collisions field indicates the possibility of network congestion. But:

  1. What may be the exact cause? How can I troubleshoot?
  2. Is there any similar to ethtool for IPIP Tunnel interface?

modinfo ipip

filename:       /lib/modules/2.6.18-194.17.1.el5/kernel/net/ipv4/ipip.ko
license:        GPL
srcversion:     288C625C7521D577F7AD9E4
depends:        tunnel4
vermagic:       2.6.18-194.17.1.el5 SMP mod_unload gcc-4.1
module_sig: 883f3504ca37590565662cff69dd0be11277ff0a08d3a3...

ip tunnel show

tunl0: ip/ip  remote any  local any  ttl inherit  nopmtudisc

UPDATE at Mon May 6 10:05:01 ICT 2013

@Danila Ladner:
Searching through Google, I found this link has same opinion with you:

My tunnel does not work:

ifconfig tunl<n> reports errors and collisions

Did you use ifconfig, perhaps ifconfig ... pointopoint ... to set up your tunnel?

Shut it down; delete it; start again with ip.

But could you please elaborate further?

@Sergey Vlasov:

tunl0     Link encap:IPIP Tunnel  HWaddr   
          inet addr:x.y.z.t  Mask:255.255.255.255
          UP RUNNING NOARP  MTU:1480  Metric:1
          RX packets:81621711099 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2 errors:692 dropped:0 overruns:0 carrier:0
          collisions:692 txqueuelen:0 
          RX bytes:16915649263419 (15.3 TiB)  TX bytes:120 (120.0 b)

I don't understand why there are 2 transmitted packets from tunl0 interface? I'm going to setup an event handler to run tcpdump whenever collisions counter is increased. Let's wait to see what happens.

UPDATE at Tue May 7 14:05:39 ICT 2013

@Danila Ladner: To exclude the possibility, I have tried your suggestion:

ifdown tun0
modprobe -r ipip
modprobe ipip
ip addr add dev tunl0 x.y.z.t/32 brd x.y.z.t
ip link set tunl0 up

I'm waiting to see if the problem is resolved:

tunl0     Link encap:IPIP Tunnel  HWaddr   
          inet addr:x.y.z.t  Mask:255.255.255.255
          UP RUNNING NOARP  MTU:1480  Metric:1
          RX packets:19630041 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:4083271398 (3.8 GiB)  TX bytes:0 (0.0 b)

Best Answer

As quanta noted I suggested him to take the tunnel down if it was built with ifconfig and rebuild it with ip. As I had a similar issue on Centos 5 kernel 2.6.25 a few years back, In my case it resolved the issue, But I was also consulting net guys and devs in IRC why that was an issue as I needed that route on production box and needed to schedule a downtime to nuke it. I do not remember exactly and as of now do not have any hard proof but Kuznetsov (original big contributor to the kernel source on the matter suggested to rebuild it with ip as he has seen issues with ifconfig. I hope this helps quanta to resolve his issue.

OFF TOPIC: So, the bottom line is i am quite dumb myself using a lot of ifconfig and it is hard to switch to ip, as long as I continue dealing with old Solaris 8 boxes and bsd boxes.

Related Topic