NIC Bonding works but can’t ping

I have bonded two NICs(Intel I-350) on CentOS 6.4. The configuration looks fine, but I am not able to ping any host and switch in its subnet.

===Bond0 status===

cat /proc/net/bonding/bond0

Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)

Bonding Mode: transmit load balancing
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 80
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: eth1
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: xx:xx:xx:xx:xx:b9
Slave queue ID: 0

Slave Interface: eth2
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: xx:xx:xx:xx:xx:ba
Slave queue ID: 0

===Interface===

bond0 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:B9
inet addr:192.168.100.2 Bcast:192.168.100.255 Mask:255.255.255.0
inet6 addr: fe80::225:90ff:fe95:cab9/64 Scope:Link
UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6162 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:369234 (360.5 KiB)

eth1 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:B9
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:3106 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:185754 (181.4 KiB)
Memory:dfb40000-dfb60000

eth2 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:BA
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:3056 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:183480 (179.1 KiB)
Memory:dfb20000-dfb40000

===Message log when ifup bond0===

Apr 3 11:01:52 HOSTNAME kernel: bonding: bond0: Setting MII monitoring interval to 80.

Apr 3 11:01:52 HOSTNAME kernel: bonding: bond0: setting mode to balance-tlb (5).

Apr 3 11:01:52 HOSTNAME kernel: bonding: bond0: Setting MII monitoring interval to 80.

Apr 3 11:01:52 HOSTNAME kernel: bonding: bond0: setting mode to balance-tlb (5).

Apr 3 11:01:52 HOSTNAME kernel: bonding: bond0: Adding slave eth1.

Apr 3 11:01:52 HOSTNAME kernel: 8021q: adding VLAN 0 to HW filter on device eth1

Apr 3 11:01:52 HOSTNAME kernel: bonding: bond0: enslaving eth1 as an active interface with a down link.

Apr 3 11:01:52 HOSTNAME kernel: bonding: bond0: Adding slave eth2.

Apr 3 11:01:52 HOSTNAME kernel: 8021q: adding VLAN 0 to HW filter on device eth2

Apr 3 11:01:52 HOSTNAME kernel: bonding: bond0: enslaving eth2 as an active interface with a down link.

Apr 3 11:01:52 HOSTNAME kernel: ADDRCONF(NETDEV_UP): bond0: link is not ready

Apr 3 11:01:52 HOSTNAME kernel: 8021q: adding VLAN 0 to HW filter on device bond0

Apr 3 11:01:55 HOSTNAME kernel: igb: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX

Apr 3 11:01:55 HOSTNAME kernel: bond0: link status definitely up for interface eth1, 1000 Mbps full duplex.

Apr 3 11:01:55 HOSTNAME kernel: bonding: bond0: making interface eth1 the new active one.

Apr 3 11:01:55 HOSTNAME kernel: bonding: bond0: first active interface up!

Apr 3 11:01:55 HOSTNAME kernel: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready

Apr 3 11:01:56 HOSTNAME kernel: igb: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX

Apr 3 11:01:56 HOSTNAME kernel: bond0: link status definitely up for interface eth2, 1000 Mbps full duplex.

Apr 3 11:01:58 HOSTNAME ntpd[2338]: Listening on interface #8 bond0, fe80::225:90ff:fe95:cab9#123 Enabled

Apr 3 11:01:58 HOSTNAME ntpd[2338]: Listening on interface #9 bond0, 192.168.100.2#123 Enabled