Ubuntu – Smartarray hpacucli command not showing individual drive status

The answer is not pleasant. There's a high probability that your array is in a "waiting for rebuild" state, where there's another failing disk in the RAID5 array set that's preventing the recovery from completing. This is why you should avoid RAID5 these days. It doesn't help that these are SATA drives... The likelihood of problems is even higher. Try powering the system off (letting the drives spin down) and powering back on. Follow the prompts at the BIOS array screen and choose the F2 option to "reenable all logical drives". This may kickstart the rebuild process.

Otherwise, it's a rebuild/recovery with new disks.

Your system is definitely underperforming based on your hardware specifications. I loaded the sysbench utility on a couple of idle HP ProLiant DL380 G6/G7 servers running CentOS 5/6 to check their performance. These are normal fixed partitions instead of LVM. (I don't typically use LVM, because of the flexibility offered by HP Smart Array controllers)

The DL380 G6 has a 6-disk RAID 1+0 array on a Smart Array P410 controller with 512MB of battery-backed cache. The DL380 G7 has a 2-disk enterprise SLC SSD array. The filesystems are XFS. I used the same sysbench command line as you did:

sysbench --init-rng=on --test=fileio --num-threads=16 --file-num=128 --file-block-size=4K --file-total-size=54G --file-test-mode=rndrd --file-fsync-freq=0 --file-fsync-end=off --max-requests=30000 run

My results were 1595 random reads-per-second across 6-disks.
On SSD, the result was 39047 random reads-per-second. Full results are at the end of this post...

• As for your setup, the first thing that jumps out at me is the size of your test partition. You're nearly filling the 60GB partition with 54GB of test files. I'm not sure if ext4 has an issue performing at 90+%, but that's the quickest thing for you to modify and retest. (or use a smaller set of test data)

• Even with LVM, there are some tuning options available on this controller/disk setup. Checking the read-ahead and changing the I/O scheduler setting from the default cfq to deadline or noop is helpful. Please see the question and answers at: Linux - real-world hardware RAID controller tuning (scsi and cciss)

• What is your RAID controller cache ratio? I typically use a 75%/25% write/read balance. This should be a quick test. The 6-disk array completed in 18 seconds. Yours took over 2 minutes.

• Can you run a bonnie++ or iozone test on the partition/array in question? It would be helpful to see if there are any other bottlenecks on the system. I wasn't familiar with sysbench, but I think these other tools will give you a better overview of the system's capabilities.

• Filesystem mount options may make a small difference, but I think the problem could be deeper than that...

hpacucli output...

Smart Array P410i in Slot 0 (Embedded)    (sn: 50123456789ABCDE)

   array A (SAS, Unused Space: 0 MB)

      logicaldrive 1 (838.1 GB, RAID 1+0, OK)

      physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 300 GB, OK)
      physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 300 GB, OK)
      physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 300 GB, OK)
      physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 300 GB, OK)
      physicaldrive 2I:1:5 (port 2I:box 1:bay 5, SAS, 300 GB, OK)
      physicaldrive 2I:1:6 (port 2I:box 1:bay 6, SAS, 300 GB, OK)

   SEP (Vendor ID PMCSIERA, Model  SRC 8x6G) 250 (WWID: 50123456789ABCED)

sysbench DL380 G6 6-disk results...

sysbench 0.4.12:  multi-threaded system evaluation benchmark

Running the test with following options:
Number of threads: 16
Initializing random number generator from timer.

Extra file open flags: 0
128 files, 432Mb each
54Gb total file size
Block size 4Kb
Number of random requests for random IO: 30000
Read/Write ratio for combined random IO test: 1.50
Using synchronous I/O mode
Doing random read test
Threads started!
Done.

Operations performed:  30001 Read, 0 Write, 0 Other = 30001 Total
Read 117.19Mb  Written 0b  Total transferred 117.19Mb  (6.2292Mb/sec)
 1594.67 Requests/sec executed

Test execution summary:
    total time:                          18.8133s
    total number of events:              30001
    total time taken by event execution: 300.7545
    per-request statistics:
         min:                                  0.00ms
         avg:                                 10.02ms
         max:                                277.41ms
         approx.  95 percentile:              25.58ms

Threads fairness:
    events (avg/stddev):           1875.0625/41.46
    execution time (avg/stddev):   18.7972/0.01

sysbench DL380 G7 SSD results...

sysbench 0.4.12:  multi-threaded system evaluation benchmark

Running the test with following options:
Number of threads: 16
Initializing random number generator from timer.


Extra file open flags: 0
128 files, 432Mb each
54Gb total file size
Block size 4Kb
Number of random requests for random IO: 30000
Read/Write ratio for combined random IO test: 1.50
Using synchronous I/O mode
Doing random read test
Threads started!
Done.

Operations performed:  30038 Read, 0 Write, 0 Other = 30038 Total
Read 117.34Mb  Written 0b  Total transferred 117.34Mb  (152.53Mb/sec)
39046.89 Requests/sec executed

Test execution summary:
    total time:                          0.7693s
    total number of events:              30038
    total time taken by event execution: 12.2631
    per-request statistics:
         min:                                  0.00ms
         avg:                                  0.41ms
         max:                                  1.89ms
         approx.  95 percentile:               0.57ms

Threads fairness:
    events (avg/stddev):           1877.3750/15.59
    execution time (avg/stddev):   0.7664/0.00