It's certainly possible to develop on a Windows machine, in fact, my first application was exclusively developed on the old Dell Precision I had at the time :)
There are three routes;
- Install OSx86 (aka iATKOS / Kalyway) on a second partition/disk and dual boot.
- Run Mac OS X Server under VMWare (Mac OS X 10.7 (Lion) onwards, read the update below).
- Use Delphi XE4 and the macincloud service. This is a commercial toolset, but the component and lib support is growing.
The first route requires modifying (or using a pre-modified) image of Leopard that can be installed on a regular PC. This is not as hard as you would think, although your success/effort ratio will depend upon how closely the hardware in your PC matches that in Mac hardware - e.g. if you're running a Core 2 Duo on an Intel Motherboard, with an NVidia graphics card you are laughing. If you're running an AMD machine or something without SSE3 it gets a little more involved.
If you purchase (or already own) a version of Leopard then this is a gray area since the Leopard EULA states you may only run it on an "Apple Labeled" machine. As many point out if you stick an Apple sticker on your PC you're probably covered.
The second option is more costly. The EULA for the workstation version of Leopard prevents it from being run under emulation and as a result, there's no support in VMWare for this. Leopard server, however, CAN be run under emulation and can be used for desktop purposes. Leopard server and VMWare are expensive, however.
If you're interested in option 1) I would suggest starting at Insanelymac and reading the OSx86 sections.
I do think you should consider whether the time you will invest is going to be worth the money you will save though. It was for me because I enjoy tinkering with this type of stuff and I started during the early iPhone betas, months before their App Store became available.
Alternatively, you could pick up a low-spec Mac Mini from eBay. You don't need much horsepower to run the SDK and you can always sell it on later if you decide to stop development or buy a better Mac.
Update: You cannot create a Mac OS X Client virtual machine for OS X 10.6 and earlier. Apple does not allow these Client OSes to be virtualized. With Mac OS X 10.7 (Lion) onwards, Apple has changed its licensing agreement in regards to virtualization. Source: VMWare KnowledgeBase
The link provided in the accepted answer shows a nice way to implement the pub/sub system using jQuery, but I found the code somewhat difficult to read, so here is my simplified version of the code:
http://jsfiddle.net/tFw89/5/
$(document).on('testEvent', function(e, eventInfo) {
subscribers = $('.subscribers-testEvent');
subscribers.trigger('testEventHandler', [eventInfo]);
});
$('#myButton').on('click', function() {
$(document).trigger('testEvent', [1011]);
});
$('#notifier1').on('testEventHandler', function(e, eventInfo) {
alert('(notifier1)The value of eventInfo is: ' + eventInfo);
});
$('#notifier2').on('testEventHandler', function(e, eventInfo) {
alert('(notifier2)The value of eventInfo is: ' + eventInfo);
});
Best Answer
Okay, this is an old subject but I'm going to add my answer to this. I can't really tell for sure whether you can use this mask for your own application even though I suspect it.
But I can tell you for sure how to use it. For starter this value masks the bits at position 24, 25, 26 and 27. You should write an enum of your own that uses this bits only, for example:
Once that is done you can register for these actions:
Every time the action MyPrimaryActionEvent is triggered, self will receive the message someAction:. Now how to trigger that action is up to the button itself. In your own UIControl subclass you can trigger the change as follow:
This will send all the actions to all the targets registered for MyPrimaryActionEvent event. And you're done.