Electronic – Generator to home wiring

A portable power bank that you can recharge elsewhere if a good idea for four MacBook. If you expect to be living in a place with no power source for a long time. You should probably check into solar, wind or hydro electricity generation. Which would be best would depend on local resources. You will need to study the purchase cost, power conversion requirements, maintenance requirements and expected lifetime of the equipment. For items like a fridge, you will need to have a storage means that is larger than a portable power bank. Care batteries are not appropriate even if they are new. There are appropriately designed lead acid batteries and other alternatives. You will need to determine the voltage level based on available large appliances of the types you want to use. The most economical strategy would probably be to use voltage converters only for the smaller loads.

You should gather information for future load anticipation, available electrical generation equipment, power conversion equipment, energy storage alternatives and charge controllers. Study how all of the components work and how small energy systems are constructed. Then you can plan and design a system to meet your needs efficiently and economically.

Chinese made grid tie inverters are currently being marketed at a price of roughly 1kW/100$USD It might be hard to find a only 1kW/1HP BLDC motor for this price, but if you can, then go for the motor generator converter. An AC generator would then need to acquired also. I don't know if the price get's better or worse with scaling (like a 5000kW rotary or a 1MW rotary) but I do know that at power generation facilities they typically use solid state conversion to convert from AC to DC (and the diodes are huge!)

Source: https://www.ge.com/reports/high-voltage-watch-ac-dc-getting-groove-back/

You'll want to check out this paper Utilization of DC motor-AC generator system to convert the solar direct current into 220v alternating current, which describes an DC to AC rotary generation system and the efficiencies. They also show that it's cheaper and more efficient. However, the efficiency curve that they used might be outdated as I've found one for a solid state inverter that is much higher than they show:

Source: www.su-kam.com/Upload/UpProductCatalogue/Solar-Roof-top-Packages-On-Grid.pdf

Source:Utilization of DC motor-AC generator system to convert the solar direct current into 220v alternating current

I'd imagine that the efficiency for the plot above would scale to a 1kW system well. In the paper they describe losses from internal heating as being large.

A soft requirement is the ability to change it’s output depending on the load. From what I’ve seen of solid-state inverters, they get very inefficient the lower you are from its rated load. The rotary inverter is a solution I’m exploring that solves that.

One thing to note about efficiency is it doesn't matter what the system is, the efficiency will drop as the power goes down. Why? because any system has a controller or circuitry that uses quiescent current. Let's say the controller takes 2W to run (you'll have to have one for both systems) for a 1kW system. If the system is converting a full load or 1kW then 2W would be 0.2% of the power to run the system. If your converting 100W or 10% of the full load the system can handle then it's 1% and finally if your converting 10W it would be 10% so in each case the efficiency will go down as the rated load goes down (as you see in the plots above).

If they can, what implementation of this do you think is the best balance between cost and power efficiency assuming all new parts?

I think a solid state grid tie inverter would be much cheaper in all cases. The cost of two motors and a controller would be much more than a solid state grid tie inverter.

Would permitting used parts change your answer?

I don't think so but if you had some parts on hand you might be able to build one cheaper. Even searching around on ebay just one 1-1.5 HP AC motor cost about 100$ to 150%, then you'd have to buy a controller and a DC motor. You can get a 1kW grid tie inverter for that much that is more efficient.

Even at 500W a solid state grid tie inverter can be had for 60$ that would cover the cost of only a used 1/2 HP AC motor on ebay currently.

The other caveat is even with the motor generator converter with solar energy you would still need an MPPT tracker to get the best power efficiency of the system.