I've been doing some reading about transformers and have gathered that they are only able to increase or decrease voltage when using AC. I was wondering whether a switching transistor circuit (the circuit that turns on and off really fast), would be enough to induce another voltage in the second coil of the transformer. I've heard that it's the switching property of AC that actually moves the electrons around. Will this constantly switching DC work?
Electronic – Powering transformers using a switching transistor circuit on DC instead of AC
transformertransistors
Related Solutions
Very nice presentation of your problem. Well done, and thanks.
(1) Check that your switch connects left to right when pressed and not top to bottom.
Remove switch - does LED go out.
Use a piece of wire. Does LED turn on?
(2) It appears that the problem is that the circuit they have given you is utterly and completely and inexplicably scrambled. It would be hard to have the circuit much wronger that that and still light the LED! It just MAY be sort of correct given several unlikely assumptions.
How can this be?
I so didn't believe what I was seeing that I checked several times.
What transistor are YOU using? What is the pinout.
Even if YOU are not using a 2N2222 they should be.
The circuit is wrong because:
They say 2n2222 so it should be NPN
It is normal to put the LED in the collector circuit but not essential.
If R3 is in collector then it should not go to V- power rail but to V+.
If we assume LED is in Emitter circuit then R1 must be in collector circuit and the transistor is being used as an "emitter follower". Not what you would usually do or for a beginner but say that's correct. And the pinout is backwards. Let's assume it is.
Then base should be being pulled +ve to turn on. It is.
They should have a pulldown on the bas to ground to turnthe transistor off - especially when used as an emitter follower. Connect another 10k from SW1/R1 junction to ground. Test . report.
BUT
Ensure transistor is CBE bottom to top as per 2N2222 datasheet or find what it really is.
Identify C B E with certainty. Ensure NPN transistor.
Collector via R3 and LED to V+
Emitter to ground
10K from Base to ground
10K via switch to V+
Like this with different values, but I have added extra 10k from base to ground (a wise precaution).
I checkd 2N2222 data sheets from several manufacturers. ALL I found including metal can ones show transistor is CBE readingUP the breadboard as shown. (terminals 48-49-50) SO there is NO DOUBT that they have the circuit VERY WRONG as shown. Their C (terminal 48( goes via R3 to B- (ground). For an NPN transistor it should be B+ / +12v. etc. Build the circuit as I have suggested. It will work ;-). Transistor MAY be dead.
Datasheets
[TO18 & TO39 metal can both the same](metal can )
All TO92 plastic seem to be ONSemi - several distributors:
Did they provide a proper circuit diagram?
If so please show it.
Update:
Here is the book concerned .
(1) The transistor is reversed. Turn it around 180 degrees and their circuit is as they intended. Their basic data shows the transistor wrongly.
(2) And / But - the circuit is an emittee follower as it was obvious it would be if you "just" reversed the transistor. This is such an 'interesting' way to do things that it was hard to believe that it was intended. It was.
Their "rather interesting" circuit:
Here is a circuit that is on by default and turns off when you apply voltage to the input.
When the input is floating or grounded Q2 is off so R2 works as a pullup resistor that turns Q1 on.
When there is a positive voltage applied to the input then Q2 turns on and sinks current trough R2, that creates a voltage drop across R2 that drops the voltage applied to the base of Q1 and turns it off.
It can also be done with mosfets with a similar logic.
Related Topic
- Electronic – arduino – Help with simple Arduino/Transistor/Solenoid circuit
- Appox. the Impedance of Single Phase Pole Transformers using only Nameplate Ratings
- Electronic – How a Joule thief works
- Electronic – NPN transistor not switching 12V from microcontroller
- Electronic – Will shorting secondary winding of transformer cause damage
- Electronic – Understand the Joule Thief circuit
- Electronic – Understanding a Single Transistor Flyback Transformer Driver
- Electronic – Designing a transformer with low usage time but high power output for small interval of time
Best Answer
Yes. In fact most MODERN power supplies use that principle. That is called "Switch-Mode Power Supply" (SMPS). It is almost required by law in new electronic equipment (including phone chargers, etc.) for efficiency greatly exceeding the old-style big "heavy-iron" transformers that ran at electric mains frequencies (50Hz and 60Hz). SMPS typically operate at 10s or 100s of KHz and use a much smaller ferrite transformer for equivalent power as the old-school "heavy iron".