It's certainly possible to develop on a Windows machine, in fact, my first application was exclusively developed on the old Dell Precision I had at the time :)
There are three routes;
- Install OSx86 (aka iATKOS / Kalyway) on a second partition/disk and dual boot.
- Run Mac OS X Server under VMWare (Mac OS X 10.7 (Lion) onwards, read the update below).
- Use Delphi XE4 and the macincloud service. This is a commercial toolset, but the component and lib support is growing.
The first route requires modifying (or using a pre-modified) image of Leopard that can be installed on a regular PC. This is not as hard as you would think, although your success/effort ratio will depend upon how closely the hardware in your PC matches that in Mac hardware - e.g. if you're running a Core 2 Duo on an Intel Motherboard, with an NVidia graphics card you are laughing. If you're running an AMD machine or something without SSE3 it gets a little more involved.
If you purchase (or already own) a version of Leopard then this is a gray area since the Leopard EULA states you may only run it on an "Apple Labeled" machine. As many point out if you stick an Apple sticker on your PC you're probably covered.
The second option is more costly. The EULA for the workstation version of Leopard prevents it from being run under emulation and as a result, there's no support in VMWare for this. Leopard server, however, CAN be run under emulation and can be used for desktop purposes. Leopard server and VMWare are expensive, however.
If you're interested in option 1) I would suggest starting at Insanelymac and reading the OSx86 sections.
I do think you should consider whether the time you will invest is going to be worth the money you will save though. It was for me because I enjoy tinkering with this type of stuff and I started during the early iPhone betas, months before their App Store became available.
Alternatively, you could pick up a low-spec Mac Mini from eBay. You don't need much horsepower to run the SDK and you can always sell it on later if you decide to stop development or buy a better Mac.
Update: You cannot create a Mac OS X Client virtual machine for OS X 10.6 and earlier. Apple does not allow these Client OSes to be virtualized. With Mac OS X 10.7 (Lion) onwards, Apple has changed its licensing agreement in regards to virtualization. Source: VMWare KnowledgeBase
I had the same problem: I first downloaded my certificates to my small MacBook while on the run. When trying to install the certificates on my iMac... then I ran into the problems described on this page.
After spending hours pulling my hair out like many of you, I performed the following steps to fix it:
Close all your stuff except your webpage that should be logged into App Dev center.
Open Xcode. Click WINDOW > ORGANIZER. Then click the Devices tab and select "Provisioning Profiles" on the left.
That should bring up your provisioning profiles. Highlight one by one (if more than 1), right click and delete profile. Yes, just do it! Delete them all! (I kept making a new one after a new one trying to make the thing work.)
From the first page you see after logging into the App Dev Center on the right side click "iOS PROVISIONING PORTAL" > (do not "launch assistant"). Instead click on the left side. Select CERTIFICATES. You will probably have just one line listed with your name/company - from there click on the right side REVOKE. Click OK to verify that's what you want to do.
On the same page click DEVICES. Click the box next to your device you are trying to provision and click REMOVE SELECTED. Again click OK to verify.
Wait about 2 minutes to let Apple do their thing.
Now click on "HOME" that is on the left side navigation.
Click "Launch Assistant"
create a new app ID - call it whatever you want. Just make sure it's unique enough to know that's the one you just created because the others you've been messing with all day will not be deleted from Apples Dev Center.
You should be able to follow the rest of the Assistant without troubles -- the main thing is you just had to delete your old provision profiles and start over.
Good Luck!
Best Answer
My problem was that, for some reason the various certs were being added to the 'System' keychain instead of the 'login' one.
By selecting 'login' and then adding them with the little '+' (next to the i) they've been added to the right place.